Difficulty
Moderate
Steps
10
Time Required
Suggest a time??
Sections
2
- General Disassembly Prerequisite Guide
- 4 steps
- Screen
- 6 steps
Flags
1
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackAzpen A701
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
General Disassembly Prerequisite Guide
- Remove the two 2cm screws on the bottom using the PH0 Phillips head screw driver.
Remove the two 2cm screws on the bottom using the PH0 Phillips head screw driver.
1024
Step 2
- Pry open back piece with plastic spudger.
- Remove the back piece of the device.
- The back panel may be difficult to pry off, use gentle force.
Pry open back piece with plastic spudger.
Remove the back piece of the device.
The back panel may be difficult to pry off, use gentle force.
Step 3
- Disconnect speaker (which is attached by black and red wires) from back piece using plastic spudger.
Disconnect speaker (which is attached by black and red wires) from back piece using plastic spudger.
Step 4
- Gently pry the battery off of the device with the plastic spudger.
- There is a large amount of glue holding the battery to the device.
- Do not puncture the battery with the plastic spudger.
Gently pry the battery off of the device with the plastic spudger.
There is a large amount of glue holding the battery to the device.
Do not puncture the battery with the plastic spudger.
Step 5
Screen
- Disconnect the two larger of the three ZIF cables by prying open the flap with a plastic spudger and gently removing the cable.
Disconnect the two larger of the three ZIF cables by prying open the flap with a plastic spudger and gently removing the cable.
Step 6
- Peel off the black tape from the corner of the motherboard (indicated by the blue surface of the device)
Peel off the black tape from the corner of the motherboard (indicated by the blue surface of the device)
Step 7
- Use PH000 Phillips head screw driver to remove the three screws that connect the motherboard to the front panel.
- When removing the motherboard be cautious of the gray wire connected from motherboard to actual device.
Use PH000 Phillips head screw driver to remove the three screws that connect the motherboard to the front panel.
When removing the motherboard be cautious of the gray wire connected from motherboard to actual device.
Step 8
- Remove motherboard and battery and set aside.
Remove motherboard and battery and set aside.
Step 9
- Remove the small orange tape attached with a gray wire from the top corner of the device. This is the antenna.
- Use plastic spudger around silver lining within the device to pry the screen off.
- The metal screen assembly is two pieces. When removing the screen, make sure to pry off both pieces at once.
Remove the small orange tape attached with a gray wire from the top corner of the device. This is the antenna.
Use plastic spudger around silver lining within the device to pry the screen off.
The metal screen assembly is two pieces. When removing the screen, make sure to pry off both pieces at once.
Step 10
- Replace broken screen and reverse steps to re-assemble device.
Replace broken screen and reverse steps to re-assemble device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Michael
Member since: 03/11/2015
568 Reputation
4 Guides authored
Badges:
15
+12 more badges
Team
Colorado Springs, Team 2-1, Panko Spring 2015
Member of Colorado Springs, Team 2-1, Panko Spring 2015
UCCS-PANKO-S15S2G1
3 Members
12 Guides authored
