Barreto Tillers E1320Htrlr 2016 Outboard Bearing Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

15

Time Required

                          20 minutes - 1 hour            

Sections

4

• Safety Precautions
• 6 steps
• Righthand Side Plate
• 5 steps
• Outboard Bearing Assembly Bolt
• 3 steps
• Outboard Bearing Assembly
• 1 step

Flags

0

• BackBarreto Tillers E1320HTRLR (2016)

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

If only the internal ball bearings need to be replaced, use this guide.

What you need

Step 1

              Disconnect the spark plug wire               

• Before you begin, ensure that the engine is powered down and cool to the touch.
• Grab the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

Before you begin, ensure that the engine is powered down and cool to the touch.

Grab the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

1024

Step 2

              Flip the engine switch to the off position               

• Flip the red engine ON/OFF switch to the OFF position.

Flip the red engine ON/OFF switch to the OFF position.

Step 3

              Close the fuel valve               

• Flip the fuel valve lever to the OFF position.

Flip the fuel valve lever to the OFF position.

Step 4

              Turn off the ignition               

• Flip the ignition switch to the OFF position.
• Ensure the wheel drive control lever is set to the neutral position.

Flip the ignition switch to the OFF position.

Ensure the wheel drive control lever is set to the neutral position.

Step 5

              Allow the wheels to freewheel               

• Pull the locking pin out and rotate it 90˚ to unlock the right wheel from the hub.
• Repeat for the left wheel.

Pull the locking pin out and rotate it 90˚ to unlock the right wheel from the hub.

Repeat for the left wheel.

Step 6

              Add wheel chocks               

• Insert wheel chocks underneath each wheel to keep the device stationary during disassembly.

Insert wheel chocks underneath each wheel to keep the device stationary during disassembly.

Step 7

              Remove the grease fitting               

• Use an 8 mm socket to remove the outboard bearing grease fitting.

Use an 8 mm socket to remove the outboard bearing grease fitting.

Step 8

              Remove the side plate bolts               

• Use a 9/16 inch socket to remove the four bolts securing the tine shaft to the side plate.
• Use a 9/16 socket and wrench to remove the five bolts and accompanying nuts securing the side plate to the frame, three on the outside and two in the wheel well.

Use a 9/16 inch socket to remove the four bolts securing the tine shaft to the side plate.

Use a 9/16 socket and wrench to remove the five bolts and accompanying nuts securing the side plate to the frame, three on the outside and two in the wheel well.

Step 9

              Tilt the tiller               

• Tilt the tiller up so the motor side is resting on the work surface with the tines raised.

Tilt the tiller up so the motor side is resting on the work surface with the tines raised.

Step 10

              Remove the tine cover bolts               

• Use a 1/2 inch socket and wrench to remove the four bolts and accompanying nuts securing the side plate to the tine cover.

Use a 1/2 inch socket and wrench to remove the four bolts and accompanying nuts securing the side plate to the tine cover.

Step 11

              Remove the side plate               

• Slide the side plate down and away from the device to remove it.

Slide the side plate down and away from the device to remove it.

Step 12

              Clean the assembly               

• Use a clean paper towel or shop rag to remove the grease from the outboard bearing assembly.

Use a clean paper towel or shop rag to remove the grease from the outboard bearing assembly.

Step 13

              Remove the outboard bearing assembly bolt               

• Use a 9/16 inch socket to remove the bolt securing the outboard bearing assembly to the tine shaft.

Use a 9/16 inch socket to remove the bolt securing the outboard bearing assembly to the tine shaft.

Step 14

              Remove the washers               

• Remove the three washers, held in place by the bolt, from the outboard bearing assembly.

Remove the three washers, held in place by the bolt, from the outboard bearing assembly.

Step 15

              Remove the outboard bearing assembly               

• Pull the assembly off of the tine shaft to remove it.

Pull the assembly off of the tine shaft to remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                    Carsten Frauenheim                     

Member since: 03/10/2020

81,713 Reputation

                                      330 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored