Difficulty

Moderate

Steps

9

Time Required

                          5 minutes - 1 hour

Sections

2

  • Safety Precautions
  • 6 steps
  • Tine
  • 3 steps

Flags

0

  • BackBarreto Tillers E1320HTRLR (2016)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Tines should be changed as often as needed. Use Loctite 271 on tine bolt threads to prevent them from loosening.

What you need

Step 1

              Disconnect the spark plug wire
  • Before you begin, ensure that the engine is powered down and cool to the touch.
  • Grab the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

Before you begin, ensure that the engine is powered down and cool to the touch.

Grab the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

1024

Step 2

              Flip the engine switch to the off position
  • Flip the red engine ON/OFF switch to the OFF position.

Flip the red engine ON/OFF switch to the OFF position.

Step 3

              Close the fuel valve
  • Flip the fuel valve lever to the OFF position.

Flip the fuel valve lever to the OFF position.

Step 4

              Turn off the ignition
  • Flip the ignition switch to the OFF position.
  • Ensure the wheel drive control lever is set to the neutral position.

Flip the ignition switch to the OFF position.

Ensure the wheel drive control lever is set to the neutral position.

Step 5

              Allow the wheels to freewheel
  • Pull the locking pin out and rotate it 90˚ to unlock the right wheel from the hub.
  • Repeat for the left wheel.

Pull the locking pin out and rotate it 90˚ to unlock the right wheel from the hub.

Repeat for the left wheel.

Step 6

              Add wheel chocks
  • Insert wheel chocks underneath each wheel to keep the device stationary during disassembly.

Insert wheel chocks underneath each wheel to keep the device stationary during disassembly.

Step 7

              Loosen the tine bolts
  • Use a 5/8 inch socket with an 11/16 inch wrench to loosen the two 5/8 inch bolts and two 11/16 inch nuts securing the tine to the tine shaft.
  • Remove the two tine nuts.

Use a 5/8 inch socket with an 11/16 inch wrench to loosen the two 5/8 inch bolts and two 11/16 inch nuts securing the tine to the tine shaft.

Remove the two tine nuts.

Step 8

              Remove the tine bolts
  • Remove the two bolts holding the tine to the tine shaft.
  • During reassembly, use Loctite 271 on tine bolt threads to prevent them from loosening.

Remove the two bolts holding the tine to the tine shaft.

During reassembly, use Loctite 271 on tine bolt threads to prevent them from loosening.

Step 9

              Remove the tine
  • Remove the tine.
  • Repeat this procedure for each tine you need to replace.
  • Keep track of each tine’s orientation.

Remove the tine.

Repeat this procedure for each tine you need to replace.

Keep track of each tine’s orientation.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                    Carsten Frauenheim

Member since: 03/10/2020

81,713 Reputation

                                      330 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored