Difficulty
Moderate
Steps
12
Time Required
15 - 20 minutes
Sections
3
- Front Panel
- 7 steps
- Back Panel
- 2 steps
- Battery Door
- 3 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackCanon PowerShot A630
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Front Panel
- Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera.
- Remove batteries.
Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera.
Remove batteries.
1024
Step 2
- Remove the three indicated .2mm screws using a Phillips #00 screwdriver.
- Gently pull off side-panel to remove it.
Remove the three indicated .2mm screws using a Phillips #00 screwdriver.
Gently pull off side-panel to remove it.
Step 3
- Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Step 4
- Remove the indicated .2mm screw using a Phillips #00 screwdriver.
- Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Phillips #00 screwdriver.
Remove the indicated .2mm screw using a Phillips #00 screwdriver.
Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Phillips #00 screwdriver.
Step 5
- Open ‘DIGITAL A/V OUT’ door on camera.
- Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Open ‘DIGITAL A/V OUT’ door on camera.
Step 6
- Grip the sides of the top panel and gently pull to separate the top panel from the camera body.
- The top panel will not completely detach.
Grip the sides of the top panel and gently pull to separate the top panel from the camera body.
The top panel will not completely detach.
Step 7
- Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels.
- Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.
Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels.
Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.
Step 8
Back Panel
- Use the spudger to gently pull back the retaining clip and pull the ribbon out.
- The top panel should now be completely detached from the camera.
- Applying too much force to the spudger may damage the retaining clip.
Use the spudger to gently pull back the retaining clip and pull the ribbon out.
The top panel should now be completely detached from the camera.
Applying too much force to the spudger may damage the retaining clip.
Step 9
- Remove .2 mm screw using a #00 Philips screwdriver.
- Gently pry off back panel to remove it.
Remove .2 mm screw using a #00 Philips screwdriver.
Gently pry off back panel to remove it.
Step 10
Battery Door
- Remover .2 mm screw using a #00 Philips screwdriver.
Remover .2 mm screw using a #00 Philips screwdriver.
Step 11
- Using tweezers, gently pull remove the small rod in the battery door hinge.
Using tweezers, gently pull remove the small rod in the battery door hinge.
Step 12
- Gently pull up on the battery door to remove it.
Gently pull up on the battery door to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Alicia Burns
Member since: 10/13/2014
550 Reputation
5 Guides authored
Badges:
15
+12 more badges
Team
Clemson, Team 2-5, Benson Fall 2014
Member of Clemson, Team 2-5, Benson Fall 2014
CLEM-BENSON-F14S2G5
4 Members
18 Guides authored
