Beats Pill 1 0 Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          20 minutes - 1 hour

Sections

Disassembling Beats Pill 1.0
6 steps
Battery
6 steps

Flags

BackBeats Pill 1.0
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Removing the Case Screws

Using the spudger, create space between the speaker covers and then remove.
On the underside of the device, remove the rubber stand with the BeatsPill logo on it.
Using an ESD-safe Phillips #0 screwdriver, remove the four screws that were underneath the rubber stand.

Using the spudger, create space between the speaker covers and then remove.

On the underside of the device, remove the rubber stand with the BeatsPill logo on it.

Using an ESD-safe Phillips #0 screwdriver, remove the four screws that were underneath the rubber stand.

1024

Step 2

              Removing Center Cover

Remove the two screws with a Phillips #0 screwdriver.
Slowly remove the center band and two clip rings until the adhesive separates. Sit to the side the clip rings and the center band

Remove the two screws with a Phillips #0 screwdriver.

Slowly remove the center band and two clip rings until the adhesive separates. Sit to the side the clip rings and the center band

Step 3

              Separate the Device

Use the spudger to pry the device apart along its seam, starting in the middle.
Open the device to separate the front and back panels.

Use the spudger to pry the device apart along its seam, starting in the middle.

Open the device to separate the front and back panels.

Step 4

              Disconnect Speaker Wiring

Carefully remove the yellow, red, black, and white wires from the motherboard.
Ground yourself when touching the motherboard.

Carefully remove the yellow, red, black, and white wires from the motherboard.

Ground yourself when touching the motherboard.

Step 5

              Disconnect NFC Sensor Wiring

Carefully remove the black and red NFC sensor wires.

Carefully remove the black and red NFC sensor wires.

Step 6

              Disconnect Control Wiring

Carefully remove the control cables (4 black, 1 red).

Carefully remove the control cables (4 black, 1 red).

Step 7

              Battery

Using a Phillips #0 Screwdriver, unscrew the four screws holding the bands that go over the battery.

Using a Phillips #0 Screwdriver, unscrew the four screws holding the bands that go over the battery.

Step 8

              Remove motherboard screws

Using the same screwdriver, remove the motherboard screws along with the rubber stoppers.

Using the same screwdriver, remove the motherboard screws along with the rubber stoppers.

Step 9

              Remove the motherboard

Gently remove the motherboard from the case
Remove the yellow NFC module with Tweezers

Gently remove the motherboard from the case

Remove the yellow NFC module with Tweezers

Step 10

              Remove the power button

Remove power button and springs.

Remove power button and springs.

Step 11

              Cut off battery

Cut off the battery wires

Cut off the battery wires

Step 12

              Attach new battery

Using a soldering iron attach the new battery to the motherboard with the red wire connecting to the 0.2 volts (+) and black wire connecting to the ground (-). See the soldering guide for more information on how to perform this step.

Using a soldering iron attach the new battery to the motherboard with the red wire connecting to the 0.2 volts (+) and black wire connecting to the ground (-). See the soldering guide for more information on how to perform this step.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      27 other people completed this guide.

Author

                                      with 9 other contributors

                    Paul Haas

Member since: 01/13/2015

766 Reputation

                                      2 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team 3-2, Hickman Winter 2015                        

                                                  Member of USF Tampa, Team 3-2, Hickman Winter 2015 



                    USFT-HICKMAN-W15S3G2                     


                                            4 Members                     


                                            6 Guides authored

felix - Jul 22, 2015

donde puedo comprar la batttery para pill beats

wtmcclure - Aug 3, 2015

Where can you buy the replacement battery

Jailene - May 30, 2017

https://www.amazon.com/dp/B072PHZ235

And it also has battery for pill 1.0, pill XL…

jmestascatcoparco - Oct 25, 2015

Could you please tell what is the yellow card in the last picture?

James Jenkins - Aug 1, 2016

Looks like the Bluetooth antenna

Introduction#

What you need#

Team#

Introduction

What you need

Team