Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
5
- Case
- 3 steps
- Microphone
- 2 steps
- Speaker
- 4 steps
- Lens Piece
- 4 steps
- Switch Cover
- 1 step
Flags
0
BackBelkin NetCam HD Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Case
- Use a wrench to loosen up the stand from the back in order to hold the NetCam more comfortably.
Use a wrench to loosen up the stand from the back in order to hold the NetCam more comfortably.
1024
Step 2
- Work a plastic opening tool into the seam and pry the face plate away from the back panel.
Work a plastic opening tool into the seam and pry the face plate away from the back panel.
Step 3
- Use pressure to separate the covers.
- When pulling the device apart, separate from the bottom up in order to avoid pulling the wiring at the top apart.
Use pressure to separate the covers.
When pulling the device apart, separate from the bottom up in order to avoid pulling the wiring at the top apart.
Step 4
Microphone
- Use tweezers to gently pull out the white attachment from the port.
- Use your fingers to pull out the white attachment from the tan port on the front of the board a little.
Use tweezers to gently pull out the white attachment from the port.
Use your fingers to pull out the white attachment from the tan port on the front of the board a little.
Step 5
- Use a pair of tweezers to wedge between the mic and the rubber guard to remove the mic from the front cover.
- If the rubber guard comes off with the mic just remove the guard from mic and place back on the front cover.
Use a pair of tweezers to wedge between the mic and the rubber guard to remove the mic from the front cover.
If the rubber guard comes off with the mic just remove the guard from mic and place back on the front cover.
Step 6
Speaker
- Use a Phillips #0 screwdriver to take out the two 1.2 mm screws on the board.
Use a Phillips #0 screwdriver to take out the two 1.2 mm screws on the board.
Step 7
- With your fingers, pull the circuit board out of the back casing.
- When pulling the board up be sure to do so carefully so you do not break the cord which is attached on the back side.
With your fingers, pull the circuit board out of the back casing.
When pulling the board up be sure to do so carefully so you do not break the cord which is attached on the back side.
Step 8
- Gently pull the speaker out of the holder from the back of the cover.
Gently pull the speaker out of the holder from the back of the cover.
Step 9
- The speaker wires are attached with the board. It can be unattached gently by pulling out the white attachment from the port.
The speaker wires are attached with the board. It can be unattached gently by pulling out the white attachment from the port.
Step 10
Lens Piece
- Flip the circuit board to the back side.
- Fold down the tape with your finger.
- With the Phillips #0 screwdriver, unscrew the two 1.2 mm screws.
Flip the circuit board to the back side.
Fold down the tape with your finger.
With the Phillips #0 screwdriver, unscrew the two 1.2 mm screws.
Step 11
- Flip the circuit board back to the other side.
- Unscrew the screw with a Phillips #0 screw driver.
Flip the circuit board back to the other side.
Unscrew the screw with a Phillips #0 screw driver.
Step 12
- Slide the attached piece from the lens holder device.
Slide the attached piece from the lens holder device.
Step 13
- Use the tweezers to pull the white attachment out from the port a little.
- Then, take your fingers and gently pull the white attachment out from the tan port.
Use the tweezers to pull the white attachment out from the port a little.
Then, take your fingers and gently pull the white attachment out from the tan port.
Step 14
Switch Cover
- On the back of the board pull the switch slowly upward to take it off.
On the back of the board pull the switch slowly upward to take it off.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Destinie DiazVerdejo
Member since: 10/04/2016
805 Reputation
7 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 3-5, Sullivan Fall 2016
Member of USF Tampa, Team 3-5, Sullivan Fall 2016
USFT-SULLIVAN-F16S3G5
4 Members
14 Guides authored
