Difficulty
Moderate
Steps
5
Time Required
35 - 40 minutes
Sections
1
- Heating Plate
- 5 steps
Flags
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackBELLA TXG-DS14
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Heating Plate
- Turn the device off and make sure it is cooled down. Then place the device in front of you and take the drawer out by placing a hand on the handle and pull towards you. Make sure the plug is out of the way before starting any of the following steps.
- Slide the clear lock away from the button and press down on the release button to release the basket from the drawer.
Turn the device off and make sure it is cooled down. Then place the device in front of you and take the drawer out by placing a hand on the handle and pull towards you. Make sure the plug is out of the way before starting any of the following steps.
Slide the clear lock away from the button and press down on the release button to release the basket from the drawer.
1024
Step 2
- Turn the device onto its side and have the bottom surface face you.
- Remove the 1.5 mm Phillips #1 screws from the bottom of the device. Rotate the screws counterclockwise with a Phillip’s #1 screwdriver.
- There should be 8 screws removed by the end of this step
- Make sure to keep the screws in a safe spot
Turn the device onto its side and have the bottom surface face you.
Remove the 1.5 mm Phillips #1 screws from the bottom of the device. Rotate the screws counterclockwise with a Phillip’s #1 screwdriver.
There should be 8 screws removed by the end of this step
Make sure to keep the screws in a safe spot
Step 3
- Place the unscrewed bottom cover next to the device without damaging the cords by extending them.
- Unscrew all the 1.2mm Phillip’s #1 screw around the silver plate by rotating them counterclockwise with Phillip’s #1 screwdriver to take the plate off.
- There should be 6 screws removed by the end of this device
Place the unscrewed bottom cover next to the device without damaging the cords by extending them.
Unscrew all the 1.2mm Phillip’s #1 screw around the silver plate by rotating them counterclockwise with Phillip’s #1 screwdriver to take the plate off.
There should be 6 screws removed by the end of this device
Step 4
- Locate 8 silver holds that holds the silver plate and black cover together.
- Use a 0.1mm Flathead screwdriver to bend the 8 silver folds toward the center of the circle to release the silver plate.
- Be careful to not cut yourself on the sharp edges of the silver folds.
Locate 8 silver holds that holds the silver plate and black cover together.
Use a 0.1mm Flathead screwdriver to bend the 8 silver folds toward the center of the circle to release the silver plate.
Be careful to not cut yourself on the sharp edges of the silver folds.
Step 5
- Remove the silver heating plate and install the new one.
- Fold the silver edges back into place and put the screws back in. For further reassembly , follow this guide in reverse order.
- When installing the new silver heating plate, make sure to not over bend the silver edges as they can easily break.
Remove the silver heating plate and install the new one.
Fold the silver edges back into place and put the screws back in. For further reassembly , follow this guide in reverse order.
When installing the new silver heating plate, make sure to not over bend the silver edges as they can easily break.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Norma Velarde
Member since: 10/19/2018
121 Reputation
1 Guide authored
Badges:
2
Team
UC Davis, Team S7-G6, Lore Fall 2018
Member of UC Davis, Team S7-G6, Lore Fall 2018
UCD-LORE-F18S7G6
3 Members
2 Guides authored
