Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
2
- Throttle Cable
- 9 steps
- Throttle Control
- 2 steps
Flags
0
BackBilly Goat Brush Cutter BC2600HHF (2015)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Throttle Cable
- Cut and remove any zip ties securing the throttle cable.
Cut and remove any zip ties securing the throttle cable.
1024
Step 2
- Use a Phillips #2 driver to remove the screw securing the lower end of the throttle cable.
Use a Phillips #2 driver to remove the screw securing the lower end of the throttle cable.
Step 3
- Remove the bracket securing the lower end of the throttle cable.
Remove the bracket securing the lower end of the throttle cable.
Step 4
- Rotate the lower end of the throttle cable to detach it from the throttle.
Rotate the lower end of the throttle cable to detach it from the throttle.
Step 5
- When reinstalling the throttle control cable, check to make sure that the throttle control moves the throttle through its full range of motion.
- If necessary, loosen the screw securing the lower end of the throttle cable and adjust the position of the cable. Re-tighten the screw and check to make sure that the throttle moves through its full range of motion.
When reinstalling the throttle control cable, check to make sure that the throttle control moves the throttle through its full range of motion.
If necessary, loosen the screw securing the lower end of the throttle cable and adjust the position of the cable. Re-tighten the screw and check to make sure that the throttle moves through its full range of motion.
Step 6
- Use a 7/16" wrench or deep socket to remove the cap from the throttle control.
Use a 7/16" wrench or deep socket to remove the cap from the throttle control.
Step 7
- Advance the throttle control to expose the gear rack containing the upper end of the throttle cable.
Advance the throttle control to expose the gear rack containing the upper end of the throttle cable.
Step 8
- Separate the gear rack from the upper end of the throttle cable.
- Lift and remove the gear rack from the throttle control.
- If the gear rack doesn’t fully detach, advance the throttle control lever a little farther.
- Lubricate the gear rack with a bit of lithium grease during reassembly.
Separate the gear rack from the upper end of the throttle cable.
Lift and remove the gear rack from the throttle control.
If the gear rack doesn’t fully detach, advance the throttle control lever a little farther.
Lubricate the gear rack with a bit of lithium grease during reassembly.
Step 9
- Use a 1/2" wrench to unscrew the upper end of the throttle cable from the throttle control.
- Slide the throttle cable down out of the bottom of the throttle control, and remove the cable.
Use a 1/2" wrench to unscrew the upper end of the throttle cable from the throttle control.
Slide the throttle cable down out of the bottom of the throttle control, and remove the cable.
Step 10
Throttle Control
- Use a Phillips #2 driver to remove the two screws securing the throttle control.
- While removing the screws, use a 3/8" wrench to counter-hold the lock nuts and prevent them from rotating.
Use a Phillips #2 driver to remove the two screws securing the throttle control.
While removing the screws, use a 3/8" wrench to counter-hold the lock nuts and prevent them from rotating.
Step 11
- Remove the throttle control.
Remove the throttle control.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
Jeff Suovanen
Member since: 08/06/2013
401,023 Reputation
261 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
