Bionaire Bap 600 Led Night Light Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

Suggest a time??

Sections

Base/Intake
2 steps
Air Filter
2 steps
Outer Shell
12 steps
LED Night Light
3 steps

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

BackBionaire BAP 600
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Base/Intake

Rotate base counterclockwise, supporting top with opposite hand.

Rotate base counterclockwise, supporting top with opposite hand.

1024

Step 2

Pull base away from housing exposing air filter.

Pull base away from housing exposing air filter.

Step 3

              Air Filter

Grab the edge of the filter housing and pull the filter away from the rest of the device.

Grab the edge of the filter housing and pull the filter away from the rest of the device.

Step 4

Gently pull apart each fold of the filter to check for abrasions or other anomalies. Clean with a dust rag if necessary.

Gently pull apart each fold of the filter to check for abrasions or other anomalies. Clean with a dust rag if necessary.

Step 5

              Outer Shell

Remove all 6 screws from the LED housing.

Remove all 6 screws from the LED housing.

Step 6

After the 6 screws are removed, remove the LED housing from the bottom of the device by lifting it off.

After the 6 screws are removed, remove the LED housing from the bottom of the device by lifting it off.

Step 7

Using two fingers lift the translucent LED cover from the inside. Repeat this step for the second tab.

Using two fingers lift the translucent LED cover from the inside. Repeat this step for the second tab.

Step 8

After lifting 45 degrees, pull the translucent tab away from thee housing. Repeat this step for the second LED cover.

After lifting 45 degrees, pull the translucent tab away from thee housing. Repeat this step for the second LED cover.

Step 9

Locate the tab about 1 inch below the top vent. Insert a flat tool laterally past the tab and press in toward the center of the device. As the tab is being held down, pull the two halves of the egg apart to keep the shell open.

Locate the tab about 1 inch below the top vent. Insert a flat tool laterally past the tab and press in toward the center of the device. As the tab is being held down, pull the two halves of the egg apart to keep the shell open.

Step 10

Locate the second tab on the back of the device approximately 2 inches above the power cord.
Insert the flat tool at a slight angle toward the left of the power cord. Depress the tab and pull the two halves of the shell apart.

Locate the second tab on the back of the device approximately 2 inches above the power cord.

Insert the flat tool at a slight angle toward the left of the power cord. Depress the tab and pull the two halves of the shell apart.

Step 11

Locate the bottom tab on the front side at the same height as the bottom tab on the back side.
Depress the tab using a flat tool at a slight angle and pull the halves apart.

Locate the bottom tab on the front side at the same height as the bottom tab on the back side.

Depress the tab using a flat tool at a slight angle and pull the halves apart.

Step 12

Locate the last tab about one inch below the top on the front side.
Depress the tab using the flat tool at a slight angle and finish pulling the removable half of the shell off.

Locate the last tab about one inch below the top on the front side.

Depress the tab using the flat tool at a slight angle and finish pulling the removable half of the shell off.

Step 13

Locate the screw housing opposite of the control board, and remove the screw.

Locate the screw housing opposite of the control board, and remove the screw.

Step 14

Locate the control board and grab it by the top and bottom firmly. Pull the board straight out being careful not to flex the circuit while removing.

Locate the control board and grab it by the top and bottom firmly. Pull the board straight out being careful not to flex the circuit while removing.

Step 15

Locate the screw that was being hidden by the control board and remove it to release the second half of the shell.

Locate the screw that was being hidden by the control board and remove it to release the second half of the shell.

Step 16

Remove the released half of the shell to finish removing the entire outer shell of the device.

Remove the released half of the shell to finish removing the entire outer shell of the device.

Step 17

              LED Night Light

Next, once you see the interior of the air purifier there will be male ports with cables coming out of these ports as seen below. Thus, it is easy as taking the two wired male port (black and red) by pulling it towards you as seen below.
Note: There will be zip ties that are connecting the black and red wires together. Cut the zip ties.

Next, once you see the interior of the air purifier there will be male ports with cables coming out of these ports as seen below. Thus, it is easy as taking the two wired male port (black and red) by pulling it towards you as seen below.

Note: There will be zip ties that are connecting the black and red wires together. Cut the zip ties.

Step 18

Note: Pull the circuit board with the LED bulb underneath the air purifier gently in order to change out the LED bulb.
Now, use a soldering kit in order to de-solder the solder that’s on the circuit board with the LED light as seen below. Hence, once you de-solder the solder from the LED light’s wires you can move on to the next step.

Note: Pull the circuit board with the LED bulb underneath the air purifier gently in order to change out the LED bulb.

Now, use a soldering kit in order to de-solder the solder that’s on the circuit board with the LED light as seen below. Hence, once you de-solder the solder from the LED light’s wires you can move on to the next step.

Step 19

Next, the last step is to gently remove the LED light from the circuit board and replace the bad LED light bulb with a new one as shown below.

Next, the last step is to gently remove the LED light from the circuit board and replace the bad LED light bulb with a new one as shown below.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Nicholas Allen Smith

Member since: 10/19/2016

131 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       IUPUI, Team 4-4, Baechle Fall 2016                        

                                                  Member of IUPUI, Team 4-4, Baechle Fall 2016 



                    IUPUI-BAECHLE-F16S4G4                     


                                            5 Members                     


                                            7 Guides authored

Markup Mishap#

Introduction#

What you need#

Team#

Markup Mishap

Introduction

What you need

Team