Bionaire Mini Tower Fan Blade Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          30 minutes            

Sections

1

• Blades
• 8 steps

Flags

0

• BackBionaire Mini Tower Fan

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Blades               

• There are 6 screws holding the entire fan together, which need to be removed to access the internals of the fan.

There are 6 screws holding the entire fan together, which need to be removed to access the internals of the fan.

1024

Step 2

• Once the screws are all off, the fan can be pulled apart with a little bit of force. However, not too much force is required.

Once the screws are all off, the fan can be pulled apart with a little bit of force. However, not too much force is required.

Step 3

• Once you have the fan apart, in order to get more maneuverability, the wire attached to the motor needs to be loosened. This can be done by removing the two screws highlighted in red.

Once you have the fan apart, in order to get more maneuverability, the wire attached to the motor needs to be loosened. This can be done by removing the two screws highlighted in red.

Step 4

• To get more maneuverability, remove the button panel. This can be done by removing the 2 screws on either side of the panel in order to fully remove it.

To get more maneuverability, remove the button panel. This can be done by removing the 2 screws on either side of the panel in order to fully remove it.

Step 5

• Carefully remove the panel by pulling on it. It should fall out easily and separate completely from its housing.

Carefully remove the panel by pulling on it. It should fall out easily and separate completely from its housing.

Step 6

• The bolt that you need to remove is inside of the pre-installed fan blades. With your pliers, grab a hold of the nut and twist to the RIGHT. This will allow you to remove the fan blades.

The bolt that you need to remove is inside of the pre-installed fan blades. With your pliers, grab a hold of the nut and twist to the RIGHT. This will allow you to remove the fan blades.

Step 7

• In order to install the new blades, there are two pieces that you have to match up. The blades and pole both have a flat side that you have to match up in order for the blades to stay on.
• Make sure when you install the blades, it blows air when it rotates in a counterclockwise fashion.

In order to install the new blades, there are two pieces that you have to match up. The blades and pole both have a flat side that you have to match up in order for the blades to stay on.

Make sure when you install the blades, it blows air when it rotates in a counterclockwise fashion.

Step 8

• Tighten the bolt to the left and you have successfully installed your new fan blades.

Tighten the bolt to the left and you have successfully installed your new fan blades.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Kyle Taggard                     

Member since: 09/29/2015

218 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       Cal Poly, Team 14-4, Green Fall 2015                        

                                                  Member of Cal Poly, Team 14-4, Green Fall 2015 



                    CPSU-GREEN-F15S14G4                     


                                            5 Members                     


                                            15 Guides authored                     

Jason Mendez - Jun 17, 2017

Reply

Thank you the instructions were spot on