Difficulty
Moderate
Steps
11
Time Required
10 minutes
Sections
5
- Air Filter
- 3 steps
- Power Supply
- 2 steps
- Control Buttons
- 3 steps
- Fan
- 2 steps
- Motherboard
- 1 step
Flags
0
BackBissell Air180
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Air Filter
- Squeeze the clip on the back panel of the bottom housing and pull the panel away from the housing, exposing the air filter.
Squeeze the clip on the back panel of the bottom housing and pull the panel away from the housing, exposing the air filter.
1024
Step 2
- Grab the sides of the filter and pull it up.
Grab the sides of the filter and pull it up.
Step 3
- Pull the filter away from the bottom housing, removing it from the rest of the device.
Pull the filter away from the bottom housing, removing it from the rest of the device.
Step 4
Power Supply
- Remove the four 18mm Phillips #1 screws connecting the bottom housing to the rest of the device.
Remove the four 18mm Phillips #1 screws connecting the bottom housing to the rest of the device.
Step 5
- Pull the bottom housing away from the rest of the device separating the power supply.
- Unplug the red cord to fully disconnect the power supply from the fan and motherboard housing.
Pull the bottom housing away from the rest of the device separating the power supply.
Unplug the red cord to fully disconnect the power supply from the fan and motherboard housing.
Step 6
Control Buttons
- Pry off the top vent, separating it from the fan and motherboard housing.
Pry off the top vent, separating it from the fan and motherboard housing.
Step 7
- Pry the button control panel up and away from the rest of the device using a spudger.
Pry the button control panel up and away from the rest of the device using a spudger.
Step 8
- Pull the wire connecting the button controls to the fan housing to fully disconnect the button controls from the device.
Pull the wire connecting the button controls to the fan housing to fully disconnect the button controls from the device.
Step 9
Fan
- Flip the motherboard and fan housing upside down to find where to disconnect the fan from the rest of the device.
- Remove the two 11 mm screws using a Phillips #1 screwdriver.
- Detach the two wires connecting the fan to the motherboard so the fan is now loose inside the housing.
Flip the motherboard and fan housing upside down to find where to disconnect the fan from the rest of the device.
Remove the two 11 mm screws using a Phillips #1 screwdriver.
Detach the two wires connecting the fan to the motherboard so the fan is now loose inside the housing.
Step 10
- Flip the motherboard and fan housing back over and pull the fan up separating it from the rest of the device.
Flip the motherboard and fan housing back over and pull the fan up separating it from the rest of the device.
Step 11
Motherboard
- Apply pressure and push out the control knob to remove the motherboard from the rest of the device.
- Removing the two 11mm Phillips #1 screws when disconnecting the fan also disconnected the motherboard from the rest of the device.
Apply pressure and push out the control knob to remove the motherboard from the rest of the device.
Removing the two 11mm Phillips #1 screws when disconnecting the fan also disconnected the motherboard from the rest of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Aleah Ramos
Member since: 10/26/2022
533 Reputation
5 Guides authored
Badges:
5
+2 more badges
Team
UMass Dartmouth, Team 3-4, Botvin Fall 2022
Member of UMass Dartmouth, Team 3-4, Botvin Fall 2022
UMASSD-BOTVIN-F22S3G4
4 Members
5 Guides authored
