Difficulty

Moderate

Steps

10

Time Required

                          6 minutes

Sections

4

  • Dirt Cup
  • 1 step
  • Power Button
  • 3 steps
  • Motherboard
  • 5 steps
  • Vacuum Motor
  • 1 step

Flags

0

  • BackBissell Pet Hair Eraser

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Dirt Cup
  • Firmly grasp the handle and press the release button.
  • Gently pull the dirt cup down and away from the vacuum body.

Firmly grasp the handle and press the release button.

Gently pull the dirt cup down and away from the vacuum body.

1024

Step 2

              Power Button
  • Remove the six 1.2 mm Philips #2 screws from the handle and base.

Remove the six 1.2 mm Philips #2 screws from the handle and base.

Step 3

  • Grasp each half of the body and gently pull apart.
  • The green handle, power button, charge light lens, and dirt cup release are not fastened in place.
  • Once the case is split apart these items may come dislodged.

Grasp each half of the body and gently pull apart.

The green handle, power button, charge light lens, and dirt cup release are not fastened in place.

Once the case is split apart these items may come dislodged.

Step 4

  • The power button can be removed by gently lifting it off the circuitry.

The power button can be removed by gently lifting it off the circuitry.

Step 5

              Motherboard
  • Remove the battery plastic hold down by lifting it off the tabs.
  • Remove the battery by lifting straight up.
  • Position the battery aside.

Remove the battery plastic hold down by lifting it off the tabs.

Remove the battery by lifting straight up.

Position the battery aside.

Step 6

  • Grasp the charger port and remove it by lifting it straight out of the case.
  • Set the charger port next to the battery.

Grasp the charger port and remove it by lifting it straight out of the case.

Set the charger port next to the battery.

Step 7

  • Remove the power button and charge LED light by gently pulling straight out of the case.
  • The vacuum motor can be removed by pulling straight out of the case.
  • All internals are now removed.
  • Set the case halves aside.

Remove the power button and charge LED light by gently pulling straight out of the case.

The vacuum motor can be removed by pulling straight out of the case.

All internals are now removed.

Set the case halves aside.

Step 8

  • Remove the two 1 mm Phillips #2 screws in the shown locations.

Remove the two 1 mm Phillips #2 screws in the shown locations.

Step 9

  • Disconnect the power leads from the vacuum motor.
  • The red power lead goes on the terminal with the visible red dot.

Disconnect the power leads from the vacuum motor.

The red power lead goes on the terminal with the visible red dot.

Step 10

              Vacuum Motor
  • Grasp the vacuum motor and housing and pull them apart.

Grasp the vacuum motor and housing and pull them apart.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Jim Lopez

Member since: 09/20/2018

568 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Central Washington University, Team S1-G1, Pengilly Fall 2018                        

                                                  Member of Central Washington University, Team S1-G1, Pengilly Fall 2018 



                    CWU-PENGILLY-F18S1G1                     


                                            4 Members                     


                                            5 Guides authored