Difficulty
Moderate
Steps
11
Time Required
30 minutes - 1 hour
Sections
1
- Brush Motor
- 11 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackBissell SpotBot Pet
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Brush Motor
- First, set your Bissell SpotBot Pet on a flat surface to begin your repair.
First, set your Bissell SpotBot Pet on a flat surface to begin your repair.
1024
Step 2
- Lift the right container vertically to remove it from the vacuum.
Lift the right container vertically to remove it from the vacuum.
Step 3
- Gently lift up the tab on the top of the vacuum and then proceed to lift the left container straight up to release it.
Gently lift up the tab on the top of the vacuum and then proceed to lift the left container straight up to release it.
Step 4
- Remove the tube from the vacuum by sliding the tube out of its holder on the side.
Remove the tube from the vacuum by sliding the tube out of its holder on the side.
Step 5
- Unscrew the 4 screws on the top of the device and gently lift the top half up.
- A ribbon cable is still attached to the underside of the top half.
Unscrew the 4 screws on the top of the device and gently lift the top half up.
A ribbon cable is still attached to the underside of the top half.
Step 6
- Unplug the ribbon cable that connects the bottom half to the control panel on the top half. Then, set the top half off to the side.
Unplug the ribbon cable that connects the bottom half to the control panel on the top half. Then, set the top half off to the side.
Step 7
- Unscrew the screw next to the white plastic wiring harness box. This will then allow you to set the white box off to the side.
Unscrew the screw next to the white plastic wiring harness box. This will then allow you to set the white box off to the side.
Step 8
- Unscrew the screws on the plastic holder on the right side of the device. Once this is done, remove the plastic holder from the vacuum.
- Unscrew the screws that mount the vacuum motor to the device as shown.
Unscrew the screws on the plastic holder on the right side of the device. Once this is done, remove the plastic holder from the vacuum.
Unscrew the screws that mount the vacuum motor to the device as shown.
Step 9
- Unplug the wires by disconnecting the section that connects the motor to the wiring harness.
Unplug the wires by disconnecting the section that connects the motor to the wiring harness.
Step 10
- Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum.
Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum.
Step 11
- Unscrew the screws for the brush motor as shown, this motor controls the automatic scrubbing mechanism.
Unscrew the screws for the brush motor as shown, this motor controls the automatic scrubbing mechanism.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 5 other contributors
Anthony Bonvino
Member since: 09/26/2017
437 Reputation
2 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S7-G3, Banghart Fall 2017
Member of Cal Poly, Team S7-G3, Banghart Fall 2017
CPSU-BANGHART-F17S7G3
4 Members
4 Guides authored
art - May 16, 2018
Reply
hi i think you did an amazing job of breaking down how to disasemble this spotbot. i have the exact same one and though it works great suction is amazing, the brushes dont spin and i took it apart completely except i didnt know where the motor was that controlled the brushes until reading this. thanks so much
