Difficulty
Easy
Steps
12
Time Required
10 - 20 minutes
Sections
2
- Disassembling Black and Decker 3-Cup Rice Cooker Outside Panel and Wire Junctions
- 9 steps
- Black and Decker 3-Cup Rice Cooker Button Mechanism Repair
- 3 steps
Flags
0
BackBlack and Decker 3-Cup Rice Cooker
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove the Lid and Bowl
- Make sure the device is unplugged before beginning disassembly!
- Lift the lid and bowl from the top of the device.
Make sure the device is unplugged before beginning disassembly!
Lift the lid and bowl from the top of the device.
1024
Step 2
Turn the Device Upside-Down
- Turn the device upside-down, so that the four legs of the device point upwards.
Turn the device upside-down, so that the four legs of the device point upwards.
Step 3
Remove the Rubber Cushions
- Each of the four legs has a rubber cushion on its bottom. For each cushion, insert a plastic opening tool between the plastic leg and rubber cushion, and pry off the rubber cushion.
Each of the four legs has a rubber cushion on its bottom. For each cushion, insert a plastic opening tool between the plastic leg and rubber cushion, and pry off the rubber cushion.
Step 4
Remove the Spanning Screw
- Using a spanner screwdriver, remove the one 10mm long 7mm diameter spanner screw from the side of the brass panel.
Using a spanner screwdriver, remove the one 10mm long 7mm diameter spanner screw from the side of the brass panel.
Step 5
Remove the Leg Screws
- Using a Phillips screwdriver, remove the 10mm long 7mm diameter Phillips-head screws from the inside of all four legs.
- The smaller leg at the bottom is now loose and not attached to the device. Set it aside.
Using a Phillips screwdriver, remove the 10mm long 7mm diameter Phillips-head screws from the inside of all four legs.
The smaller leg at the bottom is now loose and not attached to the device. Set it aside.
Step 6
Remove the Brass Plate
- Lift the brass plate off the device and set it aside.
Lift the brass plate off the device and set it aside.
Step 7
Color the Wires
- Color coordinating wire groups make it easier to identify the wire groups during reassembly.
- Inside the device, there are three junctions with wires joined by Phillips-head screws. The first is connected to two wires, and the other two are connected to three wires each.
- Unscrew the screw at the junction near the opposite side of the device from the front panel.
- Label each of the two wires at this junction with a single color of tape.
Color coordinating wire groups make it easier to identify the wire groups during reassembly.
Inside the device, there are three junctions with wires joined by Phillips-head screws. The first is connected to two wires, and the other two are connected to three wires each.
Unscrew the screw at the junction near the opposite side of the device from the front panel.
Label each of the two wires at this junction with a single color of tape.
Step 8
Label the Second Wire Junction
- Unscrew the screw at the junction just clockwise from the button panel.
- Label the three wires of this junction with tape of a second color.
Unscrew the screw at the junction just clockwise from the button panel.
Label the three wires of this junction with tape of a second color.
Step 9
Label the Third Wire Junction
- Unscrew the screw from the wire junction just behind the front panel.
- Label the three wires at this junction with a third color of tape.
Unscrew the screw from the wire junction just behind the front panel.
Label the three wires at this junction with a third color of tape.
Step 10
Check the Locking Beam
- On the inside of the device, there is a silver-colored beam leading to the center with a U-shaped brass beam poking through it.
- The U-shaped brass beam should be bent outwards so that it cannot fit through the hole in the silver-colored beam.
On the inside of the device, there is a silver-colored beam leading to the center with a U-shaped brass beam poking through it.
The U-shaped brass beam should be bent outwards so that it cannot fit through the hole in the silver-colored beam.
Step 11
Position the Brass Beam
- If the brass beam is not poking through the silver-colored beam, you will need to position it so that it is.
- Position the brass beam below the hole in the silver-colored beam and push the silver-colored beam into it, so that the brass beam pokes through.
If the brass beam is not poking through the silver-colored beam, you will need to position it so that it is.
Position the brass beam below the hole in the silver-colored beam and push the silver-colored beam into it, so that the brass beam pokes through.
Step 12
Bend the Brass Beam
- If the brass beam can’t fit through the hole in the silver-colored beam, use pliers to bend the brass beam outwards so that it does not fit through the hole in the silver-colored beam.
If the brass beam can’t fit through the hole in the silver-colored beam, use pliers to bend the brass beam outwards so that it does not fit through the hole in the silver-colored beam.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Steven Gerick
Member since: 09/22/2014
397 Reputation
3 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team 12-1, Forte Fall 2014
Member of Cal Poly, Team 12-1, Forte Fall 2014
CPSU-FORTE-F14S12G1
5 Members
7 Guides authored
