Black And Decker Bdedmt Trigger Device Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 minutes

Sections

Armature
2 steps
Trigger Device
4 steps

Flags

BackBlack and Decker BDEDMT
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Detach Matrix Attachment

Remember to disconnect the device from all external power sources.
To detach the matrix attachment piece, press down on the attachment release button located at the top of the device.
Leaving your finger pressed down on the button, simply pull on the attachment to release it.

Remember to disconnect the device from all external power sources.

To detach the matrix attachment piece, press down on the attachment release button located at the top of the device.

Leaving your finger pressed down on the button, simply pull on the attachment to release it.

1024

Step 2

              Remove Mounting Hardware

Using a JIS 1 screwdriver, unscrew seven 19mm outer screws located on the armature.
Using the same screwdriver, unscrew the 12mm outer screw located on the armature.

Using a JIS 1 screwdriver, unscrew seven 19mm outer screws located on the armature.

Using the same screwdriver, unscrew the 12mm outer screw located on the armature.

Step 3

              Trigger Device

Grab a hold of the trigger module. Gently lift the module out of the armature.
Be gentle with the module to ensure that the reverse switch is unaffected.

Grab a hold of the trigger module. Gently lift the module out of the armature.

Be gentle with the module to ensure that the reverse switch is unaffected.

Step 4

Simply roll the trigger module onto its back.
Located on on the bottom left of the module there will be a screw with the label 3.
Use your a JIS 0 screwdriver. After the screw is released, gently pull out the black wire.
The power cord is released from the trigger module.

Simply roll the trigger module onto its back.

Located on on the bottom left of the module there will be a screw with the label 3.

Use your a JIS 0 screwdriver. After the screw is released, gently pull out the black wire.

The power cord is released from the trigger module.

Step 5

Located on the bottom side there will be a labeled area with a number 2. Below the two there will be a short white wire.
Using your needle nose tweezers insert one of the ends into the release slot below the white wire.
Make sure aim the tweezers toward the wire.
Lift the end of the tweezers to release the wire.
Do not force the removal of the wire.

Located on the bottom side there will be a labeled area with a number 2. Below the two there will be a short white wire.

Using your needle nose tweezers insert one of the ends into the release slot below the white wire.

Make sure aim the tweezers toward the wire.

Lift the end of the tweezers to release the wire.

Do not force the removal of the wire.

Step 6

Located on the top of the trigger module you will see four more wires entering the module. There will be two thin black wires, a thin white wire and a thin red wire.
The steps for the removal of these four wires is the same as seen in step number five.
Remember to reinsert the wires to their corresponding slots when reassembling.
The trigger module is now completely free from the rest of the device and can be replaced.

Located on the top of the trigger module you will see four more wires entering the module. There will be two thin black wires, a thin white wire and a thin red wire.

The steps for the removal of these four wires is the same as seen in step number five.

Remember to reinsert the wires to their corresponding slots when reassembling.

The trigger module is now completely free from the rest of the device and can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    cayla dahl

Member since: 02/01/2016

247 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UW Tacoma, Team 1-2, Rose Winter 2016                        

                                                  Member of UW Tacoma, Team 1-2, Rose Winter 2016 



                    UWT-ROSE-W16S1G2                     


                                            4 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team