Difficulty

Difficult

Steps

11

Time Required

                          40 - 55 minutes

Sections

4

  • Nozzle, Filter, and Catch Bowl
  • 2 steps
  • Motor
  • 4 steps
  • Battery
  • 2 steps
  • Charging Port
  • 3 steps

Flags

2

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackBlack and Decker PHV1810 Hand Vac

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Nozzle, Filter, and Catch Bowl
  • To take off the nozzle, filter, and catch bowl first start off by pushing in the button identified with a red square and twist that part of the device toward the handle portion of the vacuum and it should click and pop off the chassis.

To take off the nozzle, filter, and catch bowl first start off by pushing in the button identified with a red square and twist that part of the device toward the handle portion of the vacuum and it should click and pop off the chassis.

1024

Step 2

  • Once the nozzle, filter and dust bowl have been removed each part can be removed from the nozzle section of the device.

Once the nozzle, filter and dust bowl have been removed each part can be removed from the nozzle section of the device.

Step 3

              Motor
  • Remove the three screws.

Remove the three screws.

Step 4

  • Flip the hand vac over and remove two screws.

Flip the hand vac over and remove two screws.

Step 5

  • Once you have successfully unscrewed the five screws holding the cover on you should be able to take the cover off.
  • Remove the L-shaped plastic hook.
  • Once the L shaped hook has been removed the motor will easily fall out of place.

Once you have successfully unscrewed the five screws holding the cover on you should be able to take the cover off.

Remove the L-shaped plastic hook.

Once the L shaped hook has been removed the motor will easily fall out of place.

Step 6

  • Once the motor has been removed from its home the two wires that are giving it power can easily be removed by pulling on them carefully.
  • This will then allow for you to replace the motor.

Once the motor has been removed from its home the two wires that are giving it power can easily be removed by pulling on them carefully.

This will then allow for you to replace the motor.

Step 7

              Battery
  • Remove the three screws highlighted with red circles.

Remove the three screws highlighted with red circles.

Step 8

  • Remove the battery by pulling it out of the slot it sits in.

Remove the battery by pulling it out of the slot it sits in.

Step 9

              Charging Port
  • To get to the charging port you will need the plastic opening tool.
  • Remove the three screws on the handle of the vacuum.

To get to the charging port you will need the plastic opening tool.

Remove the three screws on the handle of the vacuum.

Step 10

  • Use a plastic opening tool to separate the two pieces of plastic.

Use a plastic opening tool to separate the two pieces of plastic.

Step 11

  • Remove the plastic covering to the port.
  • Remove the wires to replace the charging port.

Remove the plastic covering to the port.

Remove the wires to replace the charging port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Nicholas marsoobian

Member since: 09/24/2018

474 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       The Citadel Military College of South Carolina, Team S2-G4, Eggleston Fall 2018                        

                                                  Member of The Citadel Military College of South Carolina, Team S2-G4, Eggleston Fall 2018 



                    CMCSC-EGGLESTON-F18S2G4                     


                                            3 Members                     


                                            4 Guides authored