Difficulty
Moderate
Steps
20
Time Required
20 - 30 minutes
Sections
3
- How to clean out a Black and Decker Toast R Oven
- 13 steps
- Door Spring Mechanism
- 2 steps
- Door
- 5 steps
Flags
1
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackBlack and Decker Toast R Oven TRO200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
How to clean out a Black and Decker Toast R Oven
- Make sure that the toaster is unplugged before you begin.
- Turn the toaster over with its backside face down.
- Remove the two Phillips #4 1cm screws that attach the side panels.
Make sure that the toaster is unplugged before you begin.
Turn the toaster over with its backside face down.
Remove the two Phillips #4 1cm screws that attach the side panels.
1024
Step 2
- Pull downwards (towards the bottom of the unit) and outward to remove the side panels.
Pull downwards (towards the bottom of the unit) and outward to remove the side panels.
Step 3
- Remove the metal vent piece that is below the door.
- This should slide off easily once both of the side panels are removed.
Remove the metal vent piece that is below the door.
This should slide off easily once both of the side panels are removed.
Step 4
- Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.
Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.
Step 5
- Remove the crumb tray (the bottom, metal panel) from the toaster unit.
Remove the crumb tray (the bottom, metal panel) from the toaster unit.
Step 6
- Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.
Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.
Step 7
- Remove the knobs by pulling them upward; they should slide right off.
- When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don’t fall off.
Remove the knobs by pulling them upward; they should slide right off.
When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don’t fall off.
Step 8
- Unhook the bottom of the the display panel from the toaster unit.
- It will be a little tough to pry off, but don’t be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.
Unhook the bottom of the the display panel from the toaster unit.
It will be a little tough to pry off, but don’t be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.
Step 9
- Begin to detach the back panel from the toaster unit.
- Then, unhook the rest of the display panel.
- This will also be a little tough to get off, but don’t be afraid to be forceful.
Begin to detach the back panel from the toaster unit.
Then, unhook the rest of the display panel.
This will also be a little tough to get off, but don’t be afraid to be forceful.
Step 10
- Finish removing the outside cover by lifting the lid upward.
Finish removing the outside cover by lifting the lid upward.
Step 11
- Remove the four Phillips #4 1 cm screws from the back of the unit.
Remove the four Phillips #4 1 cm screws from the back of the unit.
Step 12
- Now, you can clean the outside units of the toaster oven.
Now, you can clean the outside units of the toaster oven.
Step 13
- Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.
Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.
Step 14
Door Spring Mechanism
- Use the screwdriver to remove the spring from the unit.
- Place the screwdriver inside the spring loop.
- Pull to unhinge the spring from the back panel.
Use the screwdriver to remove the spring from the unit.
Place the screwdriver inside the spring loop.
Pull to unhinge the spring from the back panel.
Step 15
- Remove the spring from the door mechanism by pulling it off.
- Replace the old spring with a new spring.
- When inserting a new spring, make sure that the spring is connected to the lower hole of the back panel (the hole above is used for the back casing).
Remove the spring from the door mechanism by pulling it off.
Replace the old spring with a new spring.
When inserting a new spring, make sure that the spring is connected to the lower hole of the back panel (the hole above is used for the back casing).
Step 16
Door
- Use the pliers and a wrench to straighten the outdoor mechanism.
Use the pliers and a wrench to straighten the outdoor mechanism.
Step 17
- Take off the left side of the door by separating the unit from the hinge.
Take off the left side of the door by separating the unit from the hinge.
Step 18
- Separate the right side of the door from the unit as in the previous step.
Separate the right side of the door from the unit as in the previous step.
Step 19
- Separate the door mechanism from the door by tilting the door to relieve the mechanism.
Separate the door mechanism from the door by tilting the door to relieve the mechanism.
Step 20
- Unscrew the two door-handle screws.
Unscrew the two door-handle screws.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 6 other contributors
Jonathan
Member since: 09/18/2012
281 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 2-10, Propen Fall 2012
Member of Cal Poly, Team 2-10, Propen Fall 2012
CPSU-PROPEN-F12S2G10
4 Members
5 Guides authored
alo_68salud - Oct 3, 2018
Reply
sale humo al momento de prender el horno
Brian - Oct 28, 2022
Reply
Thanks - you guide helped me ix my toaster oven.
