Black And Decker Toast R Oven On Off Switch Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

How to clean out a Black and Decker Toast R Oven
13 steps
On/Off switch
4 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

BackBlack and Decker Toast R Oven TRO200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              How to clean out a Black and Decker Toast R Oven

Make sure that the toaster is unplugged before you begin.
Turn the toaster over with its backside face down.
Remove the two Phillips #4 1cm screws that attach the side panels.

Make sure that the toaster is unplugged before you begin.

Turn the toaster over with its backside face down.

Remove the two Phillips #4 1cm screws that attach the side panels.

1024

Step 2

Pull downwards (towards the bottom of the unit) and outward to remove the side panels.

Pull downwards (towards the bottom of the unit) and outward to remove the side panels.

Step 3

Remove the metal vent piece that is below the door.
This should slide off easily once both of the side panels are removed.

Remove the metal vent piece that is below the door.

This should slide off easily once both of the side panels are removed.

Step 4

Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.

Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.

Step 5

Remove the crumb tray (the bottom, metal panel) from the toaster unit.

Remove the crumb tray (the bottom, metal panel) from the toaster unit.

Step 6

Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.

Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.

Step 7

Remove the knobs by pulling them upward; they should slide right off.
When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don’t fall off.

Remove the knobs by pulling them upward; they should slide right off.

When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don’t fall off.

Step 8

Unhook the bottom of the the display panel from the toaster unit.
It will be a little tough to pry off, but don’t be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.

Unhook the bottom of the the display panel from the toaster unit.

It will be a little tough to pry off, but don’t be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.

Step 9

Begin to detach the back panel from the toaster unit.
Then, unhook the rest of the display panel.
This will also be a little tough to get off, but don’t be afraid to be forceful.

Begin to detach the back panel from the toaster unit.

Then, unhook the rest of the display panel.

This will also be a little tough to get off, but don’t be afraid to be forceful.

Step 10

Finish removing the outside cover by lifting the lid upward.

Finish removing the outside cover by lifting the lid upward.

Step 11

Remove the four Phillips #4 1 cm screws from the back of the unit.

Remove the four Phillips #4 1 cm screws from the back of the unit.

Step 12

Now, you can clean the outside units of the toaster oven.

Now, you can clean the outside units of the toaster oven.

Step 13

Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.

Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.

Step 14

              On/Off switch

Remove the two Phillips #4 1 cm screws that were under the faceplate.

Remove the two Phillips #4 1 cm screws that were under the faceplate.

Step 15

Forcefully bend back the faceplate in order to get to the knob.

Forcefully bend back the faceplate in order to get to the knob.

Step 16

Remove pin holding the On/Off switch in place.

Remove pin holding the On/Off switch in place.

Step 17

Remove switch from the opening it protrudes from.
This will take a little bit of manipulating but it will come out.

Remove switch from the opening it protrudes from.

This will take a little bit of manipulating but it will come out.

To reassemble your device, follow these instructions in reverse order. It will look like the faceplate is still bent out, but after you put the screws back in it will come back into place.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Jonathan

Member since: 09/18/2012

281 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 2-10, Propen Fall 2012                        

                                                  Member of Cal Poly, Team 2-10, Propen Fall 2012 



                    CPSU-PROPEN-F12S2G10                     


                                            4 Members                     


                                            5 Guides authored

Slice and Dice#

Needs Better Images#

Introduction#

What you need#

Team#

Slice and Dice

Needs Better Images

Introduction

What you need

Team