Black N Decker Dr500 Drill Motor Brushes Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          2 hours

Sections

Motor Brushes
20 steps

Flags

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackBlack n Decker DR500 Drill
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              B&D DR500 Drill

The drill and nameplate are shown here.
Replacement brushes are no longer available. This tells how to replace the brushes by obtaining and installing brushes from other sources. This is specifically for the DR500 drill, but the concept may apply equally well to other drills and motors.

The drill and nameplate are shown here.

Replacement brushes are no longer available. This tells how to replace the brushes by obtaining and installing brushes from other sources. This is specifically for the DR500 drill, but the concept may apply equally well to other drills and motors.

1024

Step 2

              Remove side handle

Loosen the side handle and work it back and forth while pulling it toward the chuck until it comes off.

Loosen the side handle and work it back and forth while pulling it toward the chuck until it comes off.

Step 3

              Unscrew metal nose part of body

Remove the screws from the metal nose part of the drill body. There are four screws securing it to the plastic part of the body. These require a straight screwdriver or a T20 star driver.
Be gentle, they are secured in plastic, not metal.
There is no spring force on this part, so it will not fly apart.
The location of two of the screws is shown in the picture below. There are two more in the same place on the other side.

Remove the screws from the metal nose part of the drill body. There are four screws securing it to the plastic part of the body. These require a straight screwdriver or a T20 star driver.

Be gentle, they are secured in plastic, not metal.

There is no spring force on this part, so it will not fly apart.

The location of two of the screws is shown in the picture below. There are two more in the same place on the other side.

Step 4

              Remove Metal Nose Part of Body

Remove the metal nose part by pulling it forward.
Do not tilt this part so that the chuck end points upward or the gears inside may fall out. If this happens, the picture may help you reassemble them properly.

Remove the metal nose part by pulling it forward.

Do not tilt this part so that the chuck end points upward or the gears inside may fall out. If this happens, the picture may help you reassemble them properly.

Step 5

              Remove Body Screws

Remove the five screws that secure the two halves of the plastic part of the body.
The screws require a screwdriver with a straight tip or a T15 star tip.
Locations of the screws are shown in the picture.

Remove the five screws that secure the two halves of the plastic part of the body.

The screws require a screwdriver with a straight tip or a T15 star tip.

Locations of the screws are shown in the picture.

Step 6

              Separate Plastic Body Halves

Pry the two parts of the plastic body apart at the seam.
Try to remove the half with the label by itself, leaving all the innards with the other half.

Pry the two parts of the plastic body apart at the seam.

Try to remove the half with the label by itself, leaving all the innards with the other half.

Step 7

              Observe Parts Arrangement

The gearbox is on the chuck end of the drill. It will be removed in later steps and must be reassembled in the same position. Refer to the picture.
Observe the location of the trigger and the reverse switch in the handle as well as the routing of the wires.

The gearbox is on the chuck end of the drill. It will be removed in later steps and must be reassembled in the same position. Refer to the picture.

Observe the location of the trigger and the reverse switch in the handle as well as the routing of the wires.

Step 8

              Examine the Brushes

The two brushes are graphite blocks in close-fitting brass sleeves on opposites sides of the commutator end of the stator (i.e. the end of the rotating part of the motor farthest from the chuck end of the drill). The brushes are held against the rotating commutator by brass coil springs.
Eventually the brushes wear down and become too short to contact the commutator. This causes the motor to stop running.
To check the brushes without further disassembly, look closely at the square brass sleeves. Each sleeve has a slot in the side. Looking through the slot one can see the length of the brush. The spring end of the brush should be visible in the slot as in the first picture.
If the spring end of the brush is not visible (as in the second picture), it is too worn and should be replaced.
Poke a wire or pick between the brush and commutator surface to try to move the brush back and forth in the sleeve. If it moves freely and is not too short, you probably have a completely different problem and you do not need this procedure.
If either of the brushes is too short, continue on with this procedure. If either does not move freely, you can continue with this procedure without replacing the brushes (i.e. just clean them).

The two brushes are graphite blocks in close-fitting brass sleeves on opposites sides of the commutator end of the stator (i.e. the end of the rotating part of the motor farthest from the chuck end of the drill). The brushes are held against the rotating commutator by brass coil springs.

Eventually the brushes wear down and become too short to contact the commutator. This causes the motor to stop running.

To check the brushes without further disassembly, look closely at the square brass sleeves. Each sleeve has a slot in the side. Looking through the slot one can see the length of the brush. The spring end of the brush should be visible in the slot as in the first picture.

If the spring end of the brush is not visible (as in the second picture), it is too worn and should be replaced.

Poke a wire or pick between the brush and commutator surface to try to move the brush back and forth in the sleeve. If it moves freely and is not too short, you probably have a completely different problem and you do not need this procedure.

If either of the brushes is too short, continue on with this procedure. If either does not move freely, you can continue with this procedure without replacing the brushes (i.e. just clean them).

Step 9

              Measure Brush Length

Before removing anything, estimate the brush length required. Brushes should be long enough to extend at least half way up the slot.
Brushes that are too long can be shortened easily by filing them. The shorter the brush, the sooner it will wear out and have to be replaced.
In this case a reasonable length is 3/8" (24/64").

Before removing anything, estimate the brush length required. Brushes should be long enough to extend at least half way up the slot.

Brushes that are too long can be shortened easily by filing them. The shorter the brush, the sooner it will wear out and have to be replaced.

In this case a reasonable length is 3/8" (24/64").

Step 10

              Remove Brushes

Carefully lift the motor assembly out of the plastic case,
Pull the rotor from the chuck end to slide it past the brushes.
The brushes will catch on the bearing at the end of the shaft. With a pick or wire, pull each of them back into its brass sleeve to allow it to clear the bearing. Be careful when they go past the bearing that they do not spring free and get lost.

Carefully lift the motor assembly out of the plastic case,

Pull the rotor from the chuck end to slide it past the brushes.

The brushes will catch on the bearing at the end of the shaft. With a pick or wire, pull each of them back into its brass sleeve to allow it to clear the bearing. Be careful when they go past the bearing that they do not spring free and get lost.

Step 11

              Measure Brushes Widths

When you have the brushes loose, measure the two width dimensions.
For this drill, the brush profile is a 0.233" square, essentially 15/64".

When you have the brushes loose, measure the two width dimensions.

For this drill, the brush profile is a 0.233" square, essentially 15/64".

Step 12

              Find/Make Replacement Brushes

The part is listed in numerous internet sites, but all say it is no longer available.
I could not find any suitable 15/64" x 3/8" brushes, but I did find many 15/64" brushes of longer lengths with integral connector springs.
On Ebay I got five pairs of brushes described as “15/64” x 15/64 x 11/16" Spring Carbon Brush 6x6x17mm." The total cost for all ten, including shipping from China, was $3.51.
These took several weeks to arrive, so if you need your drill soon, you may have to pay more for a domestic source.
Some of the brushes are shown. The two small pieces are the brushes removed from the drill.

The part is listed in numerous internet sites, but all say it is no longer available.

I could not find any suitable 15/64" x 3/8" brushes, but I did find many 15/64" brushes of longer lengths with integral connector springs.

On Ebay I got five pairs of brushes described as “15/64” x 15/64 x 11/16" Spring Carbon Brush 6x6x17mm." The total cost for all ten, including shipping from China, was $3.51.

These took several weeks to arrive, so if you need your drill soon, you may have to pay more for a domestic source.

Some of the brushes are shown. The two small pieces are the brushes removed from the drill.

Step 13

              Cut Brushes to Length

Mark and carefully saw two of the new brushes to 3/8" length from the end that does not have the spring attached.
The brushes are graphite, so they saw very easily. They also crush very easily, so be careful to hold and saw them gently.
The cutoff parts with the spring can be discarded.

Mark and carefully saw two of the new brushes to 3/8" length from the end that does not have the spring attached.

The brushes are graphite, so they saw very easily. They also crush very easily, so be careful to hold and saw them gently.

The cutoff parts with the spring can be discarded.

Step 14

              Check & Prepare New Brushes

If the new brushes have a curved end check whether the curve is suitable for use with the commutator. The curve is supposed to be installed so as to match the outside of the commutator. The curvature is very subtle (see picture).
In my case, the curve was an exact match for the commutator exterior, so I did not have to do anything.
If the curve on the brush is larger than that on the commutator so that the contact point is in the middle of the brushes, that should be OK. The contact between the two will wear an appropriate curve into the end of the brushes.
If the curve on the brushes is smaller than on the commutator and there are two contact points (the edges of each brush), the sharp edge may catch in the grooves of the commutator. File down the face of the brush so that it is nearly flat and the contact point is in the middle. An appropriate curve should be worn into the brush over time.

If the new brushes have a curved end check whether the curve is suitable for use with the commutator. The curve is supposed to be installed so as to match the outside of the commutator. The curvature is very subtle (see picture).

In my case, the curve was an exact match for the commutator exterior, so I did not have to do anything.

If the curve on the brush is larger than that on the commutator so that the contact point is in the middle of the brushes, that should be OK. The contact between the two will wear an appropriate curve into the end of the brushes.

If the curve on the brushes is smaller than on the commutator and there are two contact points (the edges of each brush), the sharp edge may catch in the grooves of the commutator. File down the face of the brush so that it is nearly flat and the contact point is in the middle. An appropriate curve should be worn into the brush over time.

Step 15

              Install Brushes, Assemble Motor

Insert the brushes into the brass sleeves. Be careful to insert them so that the curve in the end of the brushes is correctly placed. The sharp edges of the brush curve should be on top and bottom, not front and back.
Once the brushes are in the sleeves, push them deeply into the sleeves and slide the bearing end of the rotor through and past them.
Continue to gently push the rotor into the motor housing while using a wire or pick to pull back the brushes in turn until the brushes are on the commutator (this can be deceiving, make sure it is in far enough or the next step will fail).
This is a tricky step as the new, longer brushes have a lot of spring force on them and you must hold both back while also manipulating the rotor. A good assistant can be helpful.
If the brush was cut too long, file down the cut end until it fits.
I do not have enough hands to get a picture of this operation, so you are on your own.

Insert the brushes into the brass sleeves. Be careful to insert them so that the curve in the end of the brushes is correctly placed. The sharp edges of the brush curve should be on top and bottom, not front and back.

Once the brushes are in the sleeves, push them deeply into the sleeves and slide the bearing end of the rotor through and past them.

Continue to gently push the rotor into the motor housing while using a wire or pick to pull back the brushes in turn until the brushes are on the commutator (this can be deceiving, make sure it is in far enough or the next step will fail).

This is a tricky step as the new, longer brushes have a lot of spring force on them and you must hold both back while also manipulating the rotor. A good assistant can be helpful.

If the brush was cut too long, file down the cut end until it fits.

I do not have enough hands to get a picture of this operation, so you are on your own.

Step 16

              Install the Motor into the Case

With the innards assembled (motor, gearbox, etc), align the gearbox as observed earlier, match up the gearbox, fan, motor housing, and end bearing with their slots in the case.
All but the fan must be correctly rotated to match the housing in addition to being at the proper lengthwise position.
The gearbox alignment and the installed motor are shown.
When done, turn the splined shaft on the end of the gearbox and observe that the rest of the motor turns easily and smoothly. If it does not, break down the motor and reassemble it.

With the innards assembled (motor, gearbox, etc), align the gearbox as observed earlier, match up the gearbox, fan, motor housing, and end bearing with their slots in the case.

All but the fan must be correctly rotated to match the housing in addition to being at the proper lengthwise position.

The gearbox alignment and the installed motor are shown.

When done, turn the splined shaft on the end of the gearbox and observe that the rest of the motor turns easily and smoothly. If it does not, break down the motor and reassemble it.

Step 17

              Check & Position Reversing Lever

The reversing lever is the gray piece between the trigger and the upper part of the case.
The ball on its inner end fits into the socket at the bottom of the reversing plate on which the brushes are mounted.
Its center fits into a recess just above the inner part of the trigger.

The reversing lever is the gray piece between the trigger and the upper part of the case.

The ball on its inner end fits into the socket at the bottom of the reversing plate on which the brushes are mounted.

Its center fits into a recess just above the inner part of the trigger.

Step 18

              Reassemble the Plastic Case

Position the wires around the trigger in the appropriate gaps and put the other half of the case on the half with the motor. It should fit easily.
If it does not fit, check that 1) all wires are properly positioned, 2) the reversing lever is fitting in its recess correctly, and 3) the trigger lock on the other side of the handle it in its slot properly.
Once it comes together, secure it with the five screws removed earlier.
Check that the trigger and reversing lever move freely.

Position the wires around the trigger in the appropriate gaps and put the other half of the case on the half with the motor. It should fit easily.

If it does not fit, check that 1) all wires are properly positioned, 2) the reversing lever is fitting in its recess correctly, and 3) the trigger lock on the other side of the handle it in its slot properly.

Once it comes together, secure it with the five screws removed earlier.

Check that the trigger and reversing lever move freely.

Step 19

              Reattach the Metal Nose and Side Handle

Gently press the metal nose with the chuck onto the case. You may need to rotate the chuck or splined shaft to get them to mesh correctly.
Once in place, secure it with the four screws removed at the start of this process.
Reattach the side handle by sliding it over the chuck.

Gently press the metal nose with the chuck onto the case. You may need to rotate the chuck or splined shaft to get them to mesh correctly.

Once in place, secure it with the four screws removed at the start of this process.

Reattach the side handle by sliding it over the chuck.

Step 20

              Run the Drill

Run the drill for a few minutes to be sure it works OK and to allow the new brushes to get acquainted.
The brush replacement is complete. Use the drill as you wish.

Run the drill for a few minutes to be sure it works OK and to allow the new brushes to get acquainted.

The brush replacement is complete. Use the drill as you wish.

Reassembly instructions are included at the end.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 1 other contributor

                    Doug Ackerman

Member since: 09/09/2016

275 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

William Jaser - Feb 14, 2018

how many parts in the whole drill

William Jaser - Feb 21, 2018

soooooooooooooooooooooooooooooooooooooooooo how many parts?

obrienc87 - Nov 15, 2018

why would you need to know how many parts are in the drill?

Tom Cunningham - Jun 8, 2020

One of the best repair how-tos I’ve ever read.

William Grissom - Jul 8, 2021

Thanks for the leg-work on searching for brushes. I have the same drill, with the brushes out and ran across this fixit. I hate when one can’t easily source new brushes, but is a common problem. At least some power tools at Harbor Freight now come with spare brushes in the box. I can wait on brushes from China. I have several drills but didn’t want to toss this one, as it is my favorite for medium sized jobs.

In Progress#

Member-Contributed Guide#

Introduction#

What you need#

In Progress

Member-Contributed Guide

Introduction

What you need