Blackberry 8110 Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Display
10 steps

Flags

BackBlackberry 8110
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Removing the back cover.

Turn the phone over so that the screen is facing the table. Locate the chrome release button and push it in to unclip the battery cover.

Turn the phone over so that the screen is facing the table. Locate the chrome release button and push it in to unclip the battery cover.

1024

Step 2

              Removing the screws.

Now that the battery cover has been removed, locate the two 7.5mm Torx #T6 screws at the top of the phone. Remove these by turning counter-clockwise with your T6 screwdriver.

Now that the battery cover has been removed, locate the two 7.5mm Torx #T6 screws at the top of the phone. Remove these by turning counter-clockwise with your T6 screwdriver.

Step 3

              Removing the bottom cover.

Now that the two screws at the top have been removed, take your spudger and locate the two gaps to the left and right of the button that releases the battery cover.
With your spudger, carefully wedge it into the gap and pry downwards to release the bottom cover.

Now that the two screws at the top have been removed, take your spudger and locate the two gaps to the left and right of the button that releases the battery cover.

With your spudger, carefully wedge it into the gap and pry downwards to release the bottom cover.

Step 4

              Removng the screws from the front side.

Turn the phone over so that the screen is facing up. With the bottom cover off, you will be able to locate two 7.5mm Torx #T6 screws in each corner below the keyboard. Carefully remove these.

Turn the phone over so that the screen is facing up. With the bottom cover off, you will be able to locate two 7.5mm Torx #T6 screws in each corner below the keyboard. Carefully remove these.

Step 5

              Taking off the side panels.

Now that the screws on the front have been removed, take your spudger and wedge it between the trim on the side of the phone, and the phone itself. Carefully pry the trim away from the phone.

Now that the screws on the front have been removed, take your spudger and wedge it between the trim on the side of the phone, and the phone itself. Carefully pry the trim away from the phone.

Step 6

              Removing the back panel.

You are now ready to remove the back panel. In order to do this, locate the two clips on each side of the phone (underneath the trim that you just removed).
Once you locate these clips (four in total, two on each side), you should be able to unclip them with your fingers.
Be gentle as to not break the clips in doing so.

You are now ready to remove the back panel. In order to do this, locate the two clips on each side of the phone (underneath the trim that you just removed).

Once you locate these clips (four in total, two on each side), you should be able to unclip them with your fingers.

Be gentle as to not break the clips in doing so.

Step 7

              Removing the front panel.

The front panel is now ready to be removed from the rest of the phone. To do this, just pry the front part (with the keyboard and screen) away from the logic board of the phone with your fingers.

The front panel is now ready to be removed from the rest of the phone. To do this, just pry the front part (with the keyboard and screen) away from the logic board of the phone with your fingers.

Step 8

              Disconnecting the display

What is left after removing the panels is the logic board and screen. With the display facing up its connection to the logic board is on the top-left corner.

What is left after removing the panels is the logic board and screen. With the display facing up its connection to the logic board is on the top-left corner.

Step 9

Swing the black tab securing the display cable outwards and away from the logic board to an upright position (perpendicular to the white block). The tab’s pivot points are at the center-left and center-right of the white block.

Swing the black tab securing the display cable outwards and away from the logic board to an upright position (perpendicular to the white block). The tab’s pivot points are at the center-left and center-right of the white block.

Step 10

Remove the display cable down towards the center of the logic board and away from under the black tab. Use a spudger between the display and logic board along all sides to separate the display.

Remove the display cable down towards the center of the logic board and away from under the black tab. Use a spudger between the display and logic board along all sides to separate the display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Yaqoub Alshawaf

Member since: 09/25/2014

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       USF Tampa, Team 1-2, Brown Fall 2014                        

                                                  Member of USF Tampa, Team 1-2, Brown Fall 2014 



                    USFT-BROWN-F14S1G2                     


                                            3 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team