Difficulty
Moderate
Steps
15
Time Required
15 minutes
Sections
3
- Battery
- 3 steps
- Keyboard
- 6 steps
- Screen
- 6 steps
Flags
0
BackBlackberry Curve 9300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place your Blackberry face down in front of you.
Place your Blackberry face down in front of you.
1024
Step 2
- Locate the indent on the bottom of the back cover.
- Use your fingernail to lift and remove the back cover.
Locate the indent on the bottom of the back cover.
Use your fingernail to lift and remove the back cover.
Step 3
- From the top, use your fingernail to lift and remove the battery.
From the top, use your fingernail to lift and remove the battery.
Step 4
Keyboard
- Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
Step 5
- Place the phone face up and use tweezers to securely grip and lift the screen upwards.
Place the phone face up and use tweezers to securely grip and lift the screen upwards.
Step 6
- Use a plastic opening tool to lift the bottom edge of the front cover.
Use a plastic opening tool to lift the bottom edge of the front cover.
Step 7
- Use your nails to unclip the sides of the frame from the phone.
Use your nails to unclip the sides of the frame from the phone.
Step 8
- Lift and remove the frame.
Lift and remove the frame.
Step 9
- Lift and remove the keyboard.
Lift and remove the keyboard.
Step 10
Screen
- Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver
Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver
Step 11
- Carefully pull the keyboard base up and away from the phone.
- Disconnect the keyboard base from the phone completely.
Carefully pull the keyboard base up and away from the phone.
Disconnect the keyboard base from the phone completely.
Step 12
- Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver
Locate and remove the four 5mm screws on the top and bottom of the phone with a T6 Torx screwdriver
Step 13
- Use a plastic opening tool to find the crease below the screen.
- Insert where shown and use the tool to unclip the two sides of screen from body.
- The opening tool goes approximately midway between the top and bottom edge of the screen.
Use a plastic opening tool to find the crease below the screen.
Insert where shown and use the tool to unclip the two sides of screen from body.
The opening tool goes approximately midway between the top and bottom edge of the screen.
Step 14
- From the back of the phone, use a finger to push the front piece of the phone away from the back piece.
From the back of the phone, use a finger to push the front piece of the phone away from the back piece.
Step 15
- Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard.
Use a plastic opening tool to detach the ribbon cable from the top left corner of the screen, and separate the screen from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 6 other contributors
Alek Squires
Member since: 09/30/2013
431 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 14-7, Forte Fall 2013
Member of Cal Poly, Team 14-7, Forte Fall 2013
CPSU-FORTE-F13S14G7
5 Members
5 Guides authored
Donald Burgo - Sep 20, 2016
Reply
would appreciate new ldc part # and order info! - - !
