Difficulty
Moderate
Steps
16
Time Required
Suggest a time??
Sections
3
- Battery
- 3 steps
- Keyboard
- 6 steps
- Speaker
- 7 steps
Flags
0
BackBlackberry Curve 9300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place your Blackberry face down in front of you.
Place your Blackberry face down in front of you.
1024
Step 2
- Locate the indent on the bottom of the back cover.
- Use your fingernail to lift and remove the back cover.
Locate the indent on the bottom of the back cover.
Use your fingernail to lift and remove the back cover.
Step 3
- From the top, use your fingernail to lift and remove the battery.
From the top, use your fingernail to lift and remove the battery.
Step 4
Keyboard
- Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
Step 5
- Place the phone face up and use tweezers to securely grip and lift the screen upwards.
Place the phone face up and use tweezers to securely grip and lift the screen upwards.
Step 6
- Use a plastic opening tool to lift the bottom edge of the front cover.
Use a plastic opening tool to lift the bottom edge of the front cover.
Step 7
- Use your nails to unclip the sides of the frame from the phone.
Use your nails to unclip the sides of the frame from the phone.
Step 8
- Lift and remove the frame.
Lift and remove the frame.
Step 9
- Lift and remove the keyboard.
Lift and remove the keyboard.
Step 10
Speaker
- Locate and remove the two 5mm screws on top of the keyboard base with a T6 Torx screwdriver.
Locate and remove the two 5mm screws on top of the keyboard base with a T6 Torx screwdriver.
Step 11
- Carefully pull keyboard base up and away from phone.
- Disconnect keyboard base from phone completely.
Carefully pull keyboard base up and away from phone.
Disconnect keyboard base from phone completely.
Step 12
- Remove the four 5mm screws on the top and bottom of phone with a T6 Torx screwdriver
Remove the four 5mm screws on the top and bottom of phone with a T6 Torx screwdriver
Step 13
- Using a prying tool, find the crease below the screen.
- Insert where shown and use the tool to unclip the two sides of screen from body.
- Prying tool goes approximately midway between the top and bottom edge of the screen.
Using a prying tool, find the crease below the screen.
Insert where shown and use the tool to unclip the two sides of screen from body.
Prying tool goes approximately midway between the top and bottom edge of the screen.
Step 14
- From the back of the phone, use your finger to push the front piece of the phone away from the back piece.
From the back of the phone, use your finger to push the front piece of the phone away from the back piece.
Step 15
- Insert tweezers into the small holes on the top of the speaker.
Insert tweezers into the small holes on the top of the speaker.
Step 16
- Lift the speaker up to remove the speaker from phone.
Lift the speaker up to remove the speaker from phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 6 other contributors
Alek Squires
Member since: 09/30/2013
431 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 14-7, Forte Fall 2013
Member of Cal Poly, Team 14-7, Forte Fall 2013
CPSU-FORTE-F13S14G7
5 Members
5 Guides authored
