Blackberry Storm 9530 Front Buttons Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Battery
2 steps
SIM Card
2 steps
Back Speaker
7 steps
Motherboard
5 steps
Volume Control and Convenience Key Buttons
1 step
LCD/Touchscreen
1 step
Front Buttons
3 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missed a Step

Oops! This guide is currently missing some important steps.

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

BackBlackBerry Storm 9530
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover Removal

Locate the two switches toward the bottom corners of the device’s back cover.
Use your thumbs or fingers to push the two switches forward at the same time and detach the back cover from the device.
Check to make sure the back cover has fully detached from the device. You should be left with two separate pieces: the back cover, and the device with exposed internal hardware.

Locate the two switches toward the bottom corners of the device’s back cover.

Use your thumbs or fingers to push the two switches forward at the same time and detach the back cover from the device.

Check to make sure the back cover has fully detached from the device. You should be left with two separate pieces: the back cover, and the device with exposed internal hardware.

1024

Step 2

Identify that the battery is visible once the back cover has been removed, and locate the battery in the rectangular-shaped top half of the device.
Pry apart the battery and back of the device using the flat end of your spudger tool or using your finger if you do not have a spudger.
Your battery has a specific orientation resembling a horizontal rectangle. Make sure the gold colored leads are aligned with the gold colored strips on your battery before reassembling.

Identify that the battery is visible once the back cover has been removed, and locate the battery in the rectangular-shaped top half of the device.

Pry apart the battery and back of the device using the flat end of your spudger tool or using your finger if you do not have a spudger.

Your battery has a specific orientation resembling a horizontal rectangle. Make sure the gold colored leads are aligned with the gold colored strips on your battery before reassembling.

Step 3

              SIM Card

Locate the SIM card once the battery has been removed. The SIM card is typically located in the center of the phone, and it is secured by a metal tray.

Locate the SIM card once the battery has been removed. The SIM card is typically located in the center of the phone, and it is secured by a metal tray.

Step 4

Remove the SIM card carefully by sliding it upwards out of the metal tray. No tools are needed for this step.
Your SIM card has a specific orientation to follow when it is replaced. Make sure the gold colored leads are aligned with the gold colored strips in the SIM card tray before reassembling.

Remove the SIM card carefully by sliding it upwards out of the metal tray. No tools are needed for this step.

Your SIM card has a specific orientation to follow when it is replaced. Make sure the gold colored leads are aligned with the gold colored strips in the SIM card tray before reassembling.

Step 5

              Back Speaker

Place the opening tool underneath the camera lens’ protective plastic cover and pry them apart with gentle force.
Make sure the plastic cover has been fully removed by carefully lifting it away from the device with your fingers.

Place the opening tool underneath the camera lens’ protective plastic cover and pry them apart with gentle force.

Make sure the plastic cover has been fully removed by carefully lifting it away from the device with your fingers.

Step 6

Flip the device so that the touchscreen and Blackberry logo is facing you.
Place the opening tool underneath the front plastic cover located below the buttons with red and green phone symbols.
Lift and remove the plastic cover once the opening tool is in place. Make sure the plastic cover can be fully detached from the rest of the device.

Flip the device so that the touchscreen and Blackberry logo is facing you.

Place the opening tool underneath the front plastic cover located below the buttons with red and green phone symbols.

Lift and remove the plastic cover once the opening tool is in place. Make sure the plastic cover can be fully detached from the rest of the device.

Step 7

Remove the two bronze Torx T6 3 mm screws below the red and green phone symbols.

Remove the two bronze Torx T6 3 mm screws below the red and green phone symbols.

Step 8

Remove the four silver Torx T6 3 mm screws on the back of the device.

Remove the four silver Torx T6 3 mm screws on the back of the device.

Step 9

Pry the opening tool into the slit between the two plastic sides of the device to separate the back panel from the front panel.
Slide the opening tool across the slit until you are left with two, separated front and back panels.

Pry the opening tool into the slit between the two plastic sides of the device to separate the back panel from the front panel.

Slide the opening tool across the slit until you are left with two, separated front and back panels.

Step 10

Locate the silver speaker marked with numbers and letters on the back panel of the device.

Locate the silver speaker marked with numbers and letters on the back panel of the device.

Step 11

Place the opening tool underneath the silver speaker component.
Use the opening tool to lift the speaker off of the panel with light force.
Set the speaker aside once it has been fully removed.
When removing speakers, replacing or re-inserting them may result in looseness. This means that during re-assembly they may fall out or shift. An adhesive may be necessary to keep the speaker in place.

Place the opening tool underneath the silver speaker component.

Use the opening tool to lift the speaker off of the panel with light force.

Set the speaker aside once it has been fully removed.

When removing speakers, replacing or re-inserting them may result in looseness. This means that during re-assembly they may fall out or shift. An adhesive may be necessary to keep the speaker in place.

Step 12

              Motherboard

Locate the red tabbed pin strip connected to the motherboard. The red tabbed pin strip is located on the right-hand side of the back of the phone.
Disconnect the red tabbed pin strip from the motherboard by inserting the opening tool under the side of the tab and gently pulling upwards toward you.

Locate the red tabbed pin strip connected to the motherboard. The red tabbed pin strip is located on the right-hand side of the back of the phone.

Disconnect the red tabbed pin strip from the motherboard by inserting the opening tool under the side of the tab and gently pulling upwards toward you.

Step 13

Locate the yellow tabbed pin strip which is directly next to the original location of the red tabbed pin strip.
Disconnect the yellow tabbed pin strip from the motherboard using the same technique used to disconnect the red tabbed pin strip in the previous step.

Locate the yellow tabbed pin strip which is directly next to the original location of the red tabbed pin strip.

Disconnect the yellow tabbed pin strip from the motherboard using the same technique used to disconnect the red tabbed pin strip in the previous step.

Step 14

Disconnect the antenna cable located at the top right corner of the black panel using the opening tool.
Insert the opening tool underneath the side of the antenna connection, and gently pull upwards to disconnect the cable.

Disconnect the antenna cable located at the top right corner of the black panel using the opening tool.

Insert the opening tool underneath the side of the antenna connection, and gently pull upwards to disconnect the cable.

Step 15

Locate the second antenna connection toward the middle right area of the back panel. It is found in the corner where the red and yellow tabbed pin strips met.
Remove the antenna connection using the same method done in the previous, top antenna removal step.
Loosen the bottom metal cable grip (which pins down the cable) to separate the antenna from the motherboard entirely.

Locate the second antenna connection toward the middle right area of the back panel. It is found in the corner where the red and yellow tabbed pin strips met.

Remove the antenna connection using the same method done in the previous, top antenna removal step.

Loosen the bottom metal cable grip (which pins down the cable) to separate the antenna from the motherboard entirely.

Step 16

Remove the entire motherboard now that all the components holding it down have been removed or disconnected.
Grip the top right edge of the motherboard with your fingers and remove it by pulling it out gently.

Remove the entire motherboard now that all the components holding it down have been removed or disconnected.

Grip the top right edge of the motherboard with your fingers and remove it by pulling it out gently.

Step 17

              Volume Control and Convenience Key Buttons

Replace the volume control and convenience key buttons by replacing the entire middle panel.
Contact your plan provider or the phone manufacturer for details on obtaining a new panel.

Replace the volume control and convenience key buttons by replacing the entire middle panel.

Contact your plan provider or the phone manufacturer for details on obtaining a new panel.

Step 18

              LCD/Touchscreen

Notice that the LCD/touchscreen is placed directly beneath the side button panel.
Prepare to remove the The LCD/touchscreen which rests directly on top of the front panel of the phone.
Remove the LCD/touchscreen by pulling it off of the front panel once you have located it. No tools are necessary.

Notice that the LCD/touchscreen is placed directly beneath the side button panel.

Prepare to remove the The LCD/touchscreen which rests directly on top of the front panel of the phone.

Remove the LCD/touchscreen by pulling it off of the front panel once you have located it. No tools are necessary.

Step 19

              Front Buttons

If any one of these buttons is broken or needs replacement, then it is possible to replace the whole button strip.

If any one of these buttons is broken or needs replacement, then it is possible to replace the whole button strip.

Step 20

First, the flexible chip on the inside of the frame needs to be detached by using the prying tool.

First, the flexible chip on the inside of the frame needs to be detached by using the prying tool.

Step 21

Next, the buttons need to be pried from the front panel

Next, the buttons need to be pried from the front panel

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    melanie lim

Member since: 04/22/2014

607 Reputation

                                      6 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 9-16, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 9-16, Regan Spring 2014 



                    CPSU-REGAN-S14S9G16                     


                                            4 Members                     


                                            10 Guides authored

Needs Better Images#

Action Shots#

Missed a Step#

Missing Details#

Introduction#

What you need#

Team#