Difficulty

Moderate

Steps

14

Time Required

                          30 minutes

Sections

1

  • Cursor Key
  • 14 steps

Flags

2

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackBlackberry Torch 9810

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Phone cover
  • Remove the back cover of the phone

Remove the back cover of the phone

1024

Step 2

              Battery
  • Remove the battery

Remove the battery

Step 3

              Remove screws
  • Unscrew the four screws using the T6 screw driver.
  • If you remove the screw in red, you void the warranty!

Unscrew the four screws using the T6 screw driver.

If you remove the screw in red, you void the warranty!

Step 4

              Wiggle Wiggle
  • Slide the screen up.
  • Remove front silver trim by using a plastic opening tools and wiggle it off.
  • This is difficult to remove, but it should come off if you do it with caution.

Slide the screen up.

Remove front silver trim by using a plastic opening tools and wiggle it off.

This is difficult to remove, but it should come off if you do it with caution.

Step 5

              More screws that need to go
  • Once you remove the rim cover, you should find two more screws on the top. Unscrew them with a T-6 screw driver.

Once you remove the rim cover, you should find two more screws on the top. Unscrew them with a T-6 screw driver.

Step 6

              Remove the Back
  • Use the plastic opening tools to remove the entire back off the phone.

Use the plastic opening tools to remove the entire back off the phone.

Step 7

              Remove Ribbon Cables
  • Remove the three ribbon cables and the antenna wire by hand.
  • The cable in red is glued to the metal cap. Peel it upwards towards the battery compartment.

Remove the three ribbon cables and the antenna wire by hand.

The cable in red is glued to the metal cap. Peel it upwards towards the battery compartment.

Step 8

              Remove Logic Board
  • The logic board will easily pull straight out.

The logic board will easily pull straight out.

Step 9

              Remove Informational Sticker
  • Remove the black sticker located above the logic board that contains the phone’s serial number

Remove the black sticker located above the logic board that contains the phone’s serial number

Step 10

              Remove More Screws
  • Behind the black sticker you should find six small yellow screws. Remove them with a T4 torx screwdriver.

Behind the black sticker you should find six small yellow screws. Remove them with a T4 torx screwdriver.

Step 11

              Separate the phone
  • Carefully separate the screen from the body.
  • Make sure to be extra careful with the ribbon!

Carefully separate the screen from the body.

Make sure to be extra careful with the ribbon!

Step 12

  • Slide the silver plate up and you should find four more screws that need to be removed. Use a T-4 screw driver.
  • They are on a black cover located on the bottom of the phone. The black cover will come off

Slide the silver plate up and you should find four more screws that need to be removed. Use a T-4 screw driver.

They are on a black cover located on the bottom of the phone. The black cover will come off

Step 13

              Carefully Remove a Ribbion
  • There is one last orange ribbon cable that needs to be pulled and behind it is the cursor

There is one last orange ribbon cable that needs to be pulled and behind it is the cursor

Step 14

              Cursor Key
  • Push the cursor upwards and out of the socket.
  • Gently pull out the white box by pulling straight out of the socket to the right. This is your cursor

Push the cursor upwards and out of the socket.

Gently pull out the white box by pulling straight out of the socket to the right. This is your cursor

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Jocelyn Adorno

Member since: 10/16/2014

296 Reputation

                                      4 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       UMass Dartmouth, Team 6-6, Vijaybhaskar Fall 2014                        

                                                  Member of UMass Dartmouth, Team 6-6, Vijaybhaskar Fall 2014 



                    UMASSD-VIJAYBHASKAR-F14S6G6                     


                                            3 Members                     


                                            4 Guides authored