Difficulty
Difficult
Steps
18
Time Required
45 minutes
Sections
2
- Motherboard
- 9 steps
- Screen
- 9 steps
Flags
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
Better Introduction
Improve this guide by completing or revising its introduction.
BackBlackberry Torch 9810
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Phone cover
- Remove the back cover of the phone
Remove the back cover of the phone
1024
Step 2
Battery Removal
- Remove the battery
Remove the battery
Step 3
Remove Screws
- Unscrew the four screws using the T6 screw driver
- If you remove the screw in red, you void the warranty!
Unscrew the four screws using the T6 screw driver
If you remove the screw in red, you void the warranty!
Step 4
Wiggle Wiggle
- Remove front silver trim by using plastic opening tools and wiggle it off.
- This is difficult to remove, but it should come off if you do it with caution.
Remove front silver trim by using plastic opening tools and wiggle it off.
This is difficult to remove, but it should come off if you do it with caution.
Step 5
More Screws
- Once you remove the rim cover, you should find two more screws on the top. Unscrew them using the T6 screw driver.
Once you remove the rim cover, you should find two more screws on the top. Unscrew them using the T6 screw driver.
Step 6
Remove the Back
- Use the plastic removal tool to remove the entire back cover.
Use the plastic removal tool to remove the entire back cover.
Step 7
Small Antenna Wire
- Unplug the black antenna wire from the logic board.
Unplug the black antenna wire from the logic board.
Step 8
Remove Ribbon Cables
- Peel off the three ribbon cables
- They are orange and located on each side as well as on the top of the logic board
- The cable circled in yellow is glued to the silver cap. Pull the ribbon cable upward towards the battery area.
Peel off the three ribbon cables
They are orange and located on each side as well as on the top of the logic board
The cable circled in yellow is glued to the silver cap. Pull the ribbon cable upward towards the battery area.
Step 9
Logic Board
- Take out your logic board
Take out your logic board
Step 10
Remove More Screws
- Unscrew six small gold screws
Unscrew six small gold screws
Step 11
Remove the Screen
- Separate the screen from its frame
- After this step, you will need a torx bit smaller than a T-4. The circled display assembly can be replaced as a unit if you wish. In that case, this is the final step.
Separate the screen from its frame
After this step, you will need a torx bit smaller than a T-4. The circled display assembly can be replaced as a unit if you wish. In that case, this is the final step.
Step 12
Apply Heat to the Screen
- Heat the digitizer
Heat the digitizer
Step 13
Remove the Digizer
- Remove gold sticky film that attaches the digitizer to the screen
- Separate the digitizer from its screen
- Be careful not to tear the ribbon cable on the left side of the digitizer. That will be removed in a later step.
Remove gold sticky film that attaches the digitizer to the screen
Separate the digitizer from its screen
Be careful not to tear the ribbon cable on the left side of the digitizer. That will be removed in a later step.
Step 14
Remove More Screws
- Move the digitizer to remove both circled screws with a T-4 bit.
- The screw in red is under the screen, be careful of the ribbon cable in the top left corner.
Move the digitizer to remove both circled screws with a T-4 bit.
The screw in red is under the screen, be careful of the ribbon cable in the top left corner.
Step 15
Remove Even More Screws
- Remove the circled screws with a T-2 bit.
- Some kits do not have a bit small enough bit for these screws. If you do not have the proper bit, you should either buy one or simply replace the whole screen and digitizer assembly.
- The silver plate may be covering up the screws. If you do not see them, slide it to the other end of the assembly.
Remove the circled screws with a T-2 bit.
Some kits do not have a bit small enough bit for these screws. If you do not have the proper bit, you should either buy one or simply replace the whole screen and digitizer assembly.
The silver plate may be covering up the screws. If you do not see them, slide it to the other end of the assembly.
Step 16
Separate the Screen Assembly
- Use a plastic opening tool to separate the assembly.
Use a plastic opening tool to separate the assembly.
Step 17
Remove the Digitizer
- This ribbon cable comes out with a simple tug.
- Pull the digitizer off the face of the phone and carefully guiding the ribbon cable out of the slot.
This ribbon cable comes out with a simple tug.
Pull the digitizer off the face of the phone and carefully guiding the ribbon cable out of the slot.
Step 18
Remove the Screen
- Remove the screen using the opening tools.
- The entire back of the screen is glued to the assembly, making it more difficult to remove. Since this part is already broken, don’t be afraid to force it out.
Remove the screen using the opening tools.
The entire back of the screen is glued to the assembly, making it more difficult to remove. Since this part is already broken, don’t be afraid to force it out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Jocelyn Adorno
Member since: 10/16/2014
296 Reputation
4 Guides authored
Badges:
11
+8 more badges
Team
UMass Dartmouth, Team 6-6, Vijaybhaskar Fall 2014
Member of UMass Dartmouth, Team 6-6, Vijaybhaskar Fall 2014
UMASSD-VIJAYBHASKAR-F14S6G6
3 Members
4 Guides authored
Freddy - Sep 8, 2016
Reply
Superb wish I could get the heating instrument can u just describe?
