Blu Dash 5 0 Dual Sim Charging Port Replacement Repair Guide

Difficulty

Difficult

Steps

8

Time Required

                          35 minutes            

Sections

4

• Battery
• 2 steps
• Display Cable
• 3 steps
• Motherboard
• 1 step
• Charging Port
• 2 steps

Flags

2

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

• BackBlu Dash 5.0 Dual SIM

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Find the small slot on the bottom left corner of the back panel.
• Slide the spudger into the small slot and lightly twist it. This will cause the corner of the back panel to pop up.
• When the back panel is loose enough, use your fingers to remove it completely.

Find the small slot on the bottom left corner of the back panel.

Slide the spudger into the small slot and lightly twist it. This will cause the corner of the back panel to pop up.

When the back panel is loose enough, use your fingers to remove it completely.

1024

Step 2

• With the back panel off, you should see a large white rectangle. This is the battery. Slide the spudger under the indent on the bottom right of the battery and pull it up.

With the back panel off, you should see a large white rectangle. This is the battery. Slide the spudger under the indent on the bottom right of the battery and pull it up.

Step 3

              Display Cable               

• Using the PH00 Phillips head screwdriver unscrew the screws holding the panel down, making sure to keep track of the position of the screws.
• The screw holes with the red circle around them hold screws with a 3.5 mm length.
• The screw holes with the orange circle around them hold screws with a 2.5 mm length.

Using the PH00 Phillips head screwdriver unscrew the screws holding the panel down, making sure to keep track of the position of the screws.

The screw holes with the red circle around them hold screws with a 3.5 mm length.

The screw holes with the orange circle around them hold screws with a 2.5 mm length.

Step 4

• Insert the plastic opening tool into a corner of the plastic panel and gently pry it away from the rest of the phone.
• Do this for each corner until the panel pops up.

Insert the plastic opening tool into a corner of the plastic panel and gently pry it away from the rest of the phone.

Do this for each corner until the panel pops up.

Step 5

• Along the right side of the phone you will see a long black wire with 2 gold end pieces on the end. This is the display cable.
• To disconnect the gold end pieces from the motherboard, take the tweezers and gently but firmly pull upwards. Do this for both ends and the wire will disconnect.

Along the right side of the phone you will see a long black wire with 2 gold end pieces on the end. This is the display cable.

To disconnect the gold end pieces from the motherboard, take the tweezers and gently but firmly pull upwards. Do this for both ends and the wire will disconnect.

Step 6

              Motherboard               

• Using the tweezers, lift the tabs where the cables are connected, this unlocks the cables. The cables will slide out of sockets easily when they are unlocked. Pull from wire using tweezers as pictured.
• The red rectangles represent where the cable’s are located.
• The orange rectangles are where the cables pug into the ports. This is where you want to apply the tweezers.
• There are two black tabs and one blue tab.

Using the tweezers, lift the tabs where the cables are connected, this unlocks the cables. The cables will slide out of sockets easily when they are unlocked. Pull from wire using tweezers as pictured.

The red rectangles represent where the cable’s are located.

The orange rectangles are where the cables pug into the ports. This is where you want to apply the tweezers.

There are two black tabs and one blue tab.

Step 7

              Charging Port               

• Solder the pins on the back of the charging port. Here’s a guide to soldering: How to solder
• Soldering iron can be very hot!

Solder the pins on the back of the charging port. Here’s a guide to soldering: How to solder

Soldering iron can be very hot!

Step 8

• Pry charging port away from the board using the metal spudger.
• It’s easier to pry with the metal spudger inserted in the charging port.

Pry charging port away from the board using the metal spudger.

It’s easier to pry with the metal spudger inserted in the charging port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Jack Manley                     

Member since: 01/30/2017

114 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       IUPUI, Team 1-1, Baechle Spring 2017                        

                                                  Member of IUPUI, Team 1-1, Baechle Spring 2017 



                    IUPUI-BAECHLE-S17S1G1                     


                                            4 Members                     


                                            3 Guides authored