Difficulty
Moderate
Steps
10
Time Required
Suggest a time??
Sections
4
- Battery
- 4 steps
- Speaker
- 2 steps
- Microphone
- 3 steps
- Vibrator
- 1 step
Flags
1
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackBlu Grand M
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the two plastic plates with a plastic opening tool.
Remove the two plastic plates with a plastic opening tool.
1024
Step 2
- Using a Phillips #000 screwdriver, remove the 3mm screws. Be sure to do this for the top and bottom of the phone.
Using a Phillips #000 screwdriver, remove the 3mm screws. Be sure to do this for the top and bottom of the phone.
Step 3
- Remove SIM card tray with paperclip or SIM card tray removal tool.
- Push down on the phone beside the camera and up on the backplate with your thumbs to remove the back plate. Remove adhesive if necessary.
Remove SIM card tray with paperclip or SIM card tray removal tool.
Push down on the phone beside the camera and up on the backplate with your thumbs to remove the back plate. Remove adhesive if necessary.
Step 4
- There is a patch of adhesive underneath the battery, which can make it difficult to remove.
- Place the plastic opening tool in the highlighted indent, and push up on the battery to remove it.
There is a patch of adhesive underneath the battery, which can make it difficult to remove.
Place the plastic opening tool in the highlighted indent, and push up on the battery to remove it.
Step 5
Speaker
- Remove the exterior cover with a Torx 2 screwdriver, to remove two 3.0mm screws.
- Remove the 4.0mm screw with a Phillips #000 screwdriver.
- Using the blue plastic opening tool, remove the exterior cover.
Remove the exterior cover with a Torx 2 screwdriver, to remove two 3.0mm screws.
Remove the 4.0mm screw with a Phillips #000 screwdriver.
Using the blue plastic opening tool, remove the exterior cover.
Step 6
- Use a Phillips #000 screwdriver to remove each of the four 1.5mm screws.
- Use a Phillips #000 screwdriver to remove each of the three 3.0mm screws.
- Use the plastic opening tool to remove the speaker.
Use a Phillips #000 screwdriver to remove each of the four 1.5mm screws.
Use a Phillips #000 screwdriver to remove each of the three 3.0mm screws.
Use the plastic opening tool to remove the speaker.
Step 7
Microphone
- Disconnect the black wire with a pair of tweezers.
- The black wire can swivel out of the way to easily access the next microphone.
Disconnect the black wire with a pair of tweezers.
The black wire can swivel out of the way to easily access the next microphone.
Step 8
- Use a pair of tweezers to remove the orange data cable as shown.
Use a pair of tweezers to remove the orange data cable as shown.
Step 9
- There will be glue holding the wires down, and they can be glued back in place after.
- Use the plastic opening tool to lift the microphone out of place.
- Use a pair of tweezers to lift the microphone out of the phone.
There will be glue holding the wires down, and they can be glued back in place after.
Use the plastic opening tool to lift the microphone out of place.
Use a pair of tweezers to lift the microphone out of the phone.
Step 10
Vibrator
- To remove the vibrator, use the plastic opening tool to pry it out.
To remove the vibrator, use the plastic opening tool to pry it out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Cameron Retzlaff
Member since: 09/17/2018
608 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Washington State, Team S9-G2, Hope Fall 2018
Member of Washington State, Team S9-G2, Hope Fall 2018
WSU-HOPE-F18S9G2
3 Members
5 Guides authored
