Difficulty

Moderate

Steps

10

Time Required

                          10 minutes

Sections

2

  • Battery
  • 3 steps
  • Motherboard
  • 7 steps

Flags

0

  • BackBLU Life X8

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Flip the phone over so that the screen is facing down.
  • Slide the opening tool between the micro-USB port and the back cover.
  • Use the opening tool to create a gap.

Flip the phone over so that the screen is facing down.

Slide the opening tool between the micro-USB port and the back cover.

Use the opening tool to create a gap.

1024

Step 2

  • Use your thumb to pry off the back panel once the gap is large enough.

Use your thumb to pry off the back panel once the gap is large enough.

Step 3

  • Once the back panel is off, locate the indent at the bottom of the battery.
  • Use your thumb to slip the battery out of the case.

Once the back panel is off, locate the indent at the bottom of the battery.

Use your thumb to slip the battery out of the case.

Step 4

              Motherboard
  • Use the Phillips #00 bit to undo the nine 1.5mm screws from the back of the device.

Use the Phillips #00 bit to undo the nine 1.5mm screws from the back of the device.

Step 5

  • Wedge the opening tool into the seam of between the screen and the gray frame.
  • Run the opening tool along the seam to release the clips that hold the two pieces together.
  • You may need to use the opening picks to prevent the clips from re-engaging.

Wedge the opening tool into the seam of between the screen and the gray frame.

Run the opening tool along the seam to release the clips that hold the two pieces together.

You may need to use the opening picks to prevent the clips from re-engaging.

Step 6

  • Once all the clips have been released, lift the frame and set it aside.

Once all the clips have been released, lift the frame and set it aside.

Step 7

  • Use the Phillips #00 Phillips bit to undo the two 1.5mm screws from the motherboard.

Use the Phillips #00 Phillips bit to undo the two 1.5mm screws from the motherboard.

Step 8

  • Use the tweezers to peel away the mesh tape and reveal the ribbon connectors.
  • Use the tweezers to lift the brown and black tabs to release the ribbon cables and unlock them.

Use the tweezers to peel away the mesh tape and reveal the ribbon connectors.

Use the tweezers to lift the brown and black tabs to release the ribbon cables and unlock them.

Step 9

  • The ribbon cables should be free. Pull back on the ribbons to release them from their connectors.

The ribbon cables should be free. Pull back on the ribbons to release them from their connectors.

Step 10

  • Slowly lift the vibration motor away from the frame and peel up the tape.

Slowly lift the vibration motor away from the frame and peel up the tape.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Alexander Prasil

Member since: 09/28/2017

543 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team S1-G2, Nance Fall 2017                        

                                                  Member of USF Tampa, Team S1-G2, Nance Fall 2017 



                    USFT-NANCE-F17S1G2                     


                                            4 Members                     


                                            6 Guides authored