Blu Studio 5 0 Ii Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Battery
3 steps
Back Case
2 steps
Motherboard
4 steps

Flags

BackBLU Studio 5.0 II
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn off your phone before disassembling the device.
Locate the small opening on the bottom corner of the back case.

Turn off your phone before disassembling the device.

Locate the small opening on the bottom corner of the back case.

1024

Step 2

Use your finger to open the back case by slowly pulling it on the open slot.
Once the case is lifted on the corner, slide your finger along the edge of the phone to remove the rest of the case.

Use your finger to open the back case by slowly pulling it on the open slot.

Once the case is lifted on the corner, slide your finger along the edge of the phone to remove the rest of the case.

Step 3

Locate the opening slot at the bottom of the battery.
Use your finger to lift the battery and remove it from the case.

Locate the opening slot at the bottom of the battery.

Use your finger to lift the battery and remove it from the case.

Step 4

              Back Case

Locate the four 3mm screws on each side of the back panel.
Use a Phillips #00 screwdriver to remove the eight screws.

Locate the four 3mm screws on each side of the back panel.

Use a Phillips #00 screwdriver to remove the eight screws.

Step 5

Carefully use a spudger to start opening the back case by inserting it between the black and blue lines on the side of the phone.
With the help of your fingers, continue to remove the back case by sliding it through the opening.

Carefully use a spudger to start opening the back case by inserting it between the black and blue lines on the side of the phone.

With the help of your fingers, continue to remove the back case by sliding it through the opening.

Step 6

              Motherboard

Locate the following adhesive buttons on the right and left side of the motherboard. These are the volume and power buttons.
Use a spudger to carefully separate them from the circuit board.

Locate the following adhesive buttons on the right and left side of the motherboard. These are the volume and power buttons.

Use a spudger to carefully separate them from the circuit board.

Step 7

Locate these two ZIF connectors on the top and left side of the motherboard.
Use a spudger to flip up and unlock the black tab on the connector.
Use tweezers to pull the ribbon cables out of their connectors.

Locate these two ZIF connectors on the top and left side of the motherboard.

Use a spudger to flip up and unlock the black tab on the connector.

Use tweezers to pull the ribbon cables out of their connectors.

Step 8

Locate the indicated connector on the top side of the motherboard.
Use a pair of tweezers to gently lift the connector from the circuit board.

Locate the indicated connector on the top side of the motherboard.

Use a pair of tweezers to gently lift the connector from the circuit board.

Step 9

Remove the three 3mm screws on the motherboard using a Phillips #00 screwdriver.
Use a spudger or tweezers to carefully lift and remove the motherboard.

Remove the three 3mm screws on the motherboard using a Phillips #00 screwdriver.

Use a spudger or tweezers to carefully lift and remove the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Ricardo Sarabia

Member since: 02/09/2016

1,042 Reputation

                                      6 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team 7-5, Cheng Spring 2016                        

                                                  Member of USF Tampa, Team 7-5, Cheng Spring 2016 



                    USFT-CHENG-S16S7G5                     


                                            3 Members                     


                                            7 Guides authored

Rodolfo Leal - Mar 1, 2017

that left the speaker disconnected?

Introduction#

What you need#

Team#

Introduction

What you need

Team