Difficulty
Moderate
Steps
8
Time Required
Suggest a time??
Sections
2
- Battery
- 2 steps
- Micro USB Port
- 6 steps
Flags
1
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
BackBLU Studio 5.5
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip over your Studio 5.5 so the back is facing you.
- Use either the spudger or your fingernail to pull up on the slot in the lower left corner and remove the back cover.
Flip over your Studio 5.5 so the back is facing you.
Use either the spudger or your fingernail to pull up on the slot in the lower left corner and remove the back cover.
1024
Step 2
- Place your finger in the small groove beneath the battery.
- Push the battery toward the top of the phone and lift it out.
Place your finger in the small groove beneath the battery.
Push the battery toward the top of the phone and lift it out.
Step 3
Micro USB Port
- Begin by removing the 12 screws along the back of the device.
- 1 of these screws will be underneath a white sticker. Just press the screwdriver through it and remove it normally.
- 5 of these screws are 3.5mm, while the remaining 7 are 5mm.
Begin by removing the 12 screws along the back of the device.
1 of these screws will be underneath a white sticker. Just press the screwdriver through it and remove it normally.
5 of these screws are 3.5mm, while the remaining 7 are 5mm.
Step 4
- Using your plastic opening tool, begin carefully prying the plastic shell from the phone.
- Make your way around the edge slowly and lift the shell off when you have made a full circuit.
Using your plastic opening tool, begin carefully prying the plastic shell from the phone.
Make your way around the edge slowly and lift the shell off when you have made a full circuit.
Step 5
- Using your tweezers, locate the small gold-colored plug in the bottom left corner and pull it straight out.
Using your tweezers, locate the small gold-colored plug in the bottom left corner and pull it straight out.
Step 6
- Use the tweezers again to pull out a small black plug in the bottom middle.
Use the tweezers again to pull out a small black plug in the bottom middle.
Step 7
- Grip the entire circuit board firmly with your tweezers and pull it towards the bottom of the phone and out.
Grip the entire circuit board firmly with your tweezers and pull it towards the bottom of the phone and out.
Step 8
- Pry the speaker from the phone with your tweezers.
- The speaker is glued to the rest of the phone and soldered to the circuit board.
Pry the speaker from the phone with your tweezers.
The speaker is glued to the rest of the phone and soldered to the circuit board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 2 other contributors
Brian Sullivan
Member since: 10/22/2014
647 Reputation
3 Guides authored
Badges:
8
+5 more badges
Team
UMass Dartmouth, Team 1-2, Shastany Fall 2014
Member of UMass Dartmouth, Team 1-2, Shastany Fall 2014
UMASSD-SHASTANY-F14S1G2
3 Members
3 Guides authored
branfay1 - Mar 2, 2016
Reply
Should I change the other parts aswell?
muhammadfaisalkhan98 - Jan 1, 2017
Reply
i want buy chargin port sir my blue cahrging port was dead plz help me i want buy
PoPeYe MaStEr - Mar 12, 2018
Reply
Where do i buy the %#*@ micro usb port
