Difficulty
Moderate
Steps
8
Time Required
10 minutes
Sections
4
- Back Case
- 2 steps
- Battery
- 1 step
- Midframe
- 3 steps
- Front Facing Camera
- 2 steps
Flags
0
BackBlu Studio 5.5 S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Casing
- In order to remove the back case, start by flipping the phone to the back side and look at it from the top.
In order to remove the back case, start by flipping the phone to the back side and look at it from the top.
1024
Step 2
Applying Pressure
- Place your finger in the small notch on the left side of the charging port (facing from the back).
- Once your finger is in the notch, pull the back case towards yourself to remove it.
Place your finger in the small notch on the left side of the charging port (facing from the back).
Once your finger is in the notch, pull the back case towards yourself to remove it.
Step 3
Battery
- Once the back case is removed, locate the battery. It is the large brick embedded in the phone. It has BLU Products, a caution statement, and a barcode on it.
- Insert your finger into the notch near the lower left of the battery, apply pressure and lift up.
Once the back case is removed, locate the battery. It is the large brick embedded in the phone. It has BLU Products, a caution statement, and a barcode on it.
Insert your finger into the notch near the lower left of the battery, apply pressure and lift up.
Step 4
Midframe
- The speaker is located behind the inner back case. Using a Phillips #0 screwdriver, unscrew the 10, 7mm screws.
- Using the Phillips #00 screwdriver, unscrew the two, 10mm screws at the bottom.
The speaker is located behind the inner back case. Using a Phillips #0 screwdriver, unscrew the 10, 7mm screws.
Using the Phillips #00 screwdriver, unscrew the two, 10mm screws at the bottom.
Step 5
Aesthetic Bottom Case
- Apply pressure and pop off the bottom aesthetic case, being careful not to break it.
Apply pressure and pop off the bottom aesthetic case, being careful not to break it.
Step 6
- Use the Spudger to pop the inner back casing off. Do this by lightly raising the side of the battery housing, then sliding the Spudger around the case.
- Pick up the inner back case and flip it over.
Use the Spudger to pop the inner back casing off. Do this by lightly raising the side of the battery housing, then sliding the Spudger around the case.
Pick up the inner back case and flip it over.
Step 7
Frontward Facing Camera
- The frontward facing camera is located in the top left of the phone. It is connected to the motherboard by a ribbon connector, and a prong system.
- Use a spudger to detach the front facing camera by flipping the orange tab on the top of the prong system.
- Once the orange tab is up, pull out the orange ribbon wire.
The frontward facing camera is located in the top left of the phone. It is connected to the motherboard by a ribbon connector, and a prong system.
Use a spudger to detach the front facing camera by flipping the orange tab on the top of the prong system.
Once the orange tab is up, pull out the orange ribbon wire.
Step 8
- Use tweezers to pick up the ribbon wire, and lift. The frontward facing camera will follow suit.
Use tweezers to pick up the ribbon wire, and lift. The frontward facing camera will follow suit.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Cody Dyl
Member since: 10/27/2014
783 Reputation
5 Guides authored
Badges:
14
+11 more badges
Team
UMass Dartmouth, Team 4-8, Miles Fall 2014
Member of UMass Dartmouth, Team 4-8, Miles Fall 2014
UMASSD-MILES-F14S4G8
2 Members
6 Guides authored
