Difficulty
Moderate
Steps
7
Time Required
15 minutes
Sections
4
- Back Case
- 2 steps
- Battery
- 1 step
- Midframe
- 3 steps
- Rear Facing Camera
- 1 step
Flags
0
BackBlu Studio 5.5 S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Casing
- In order to remove the back case, start by flipping the phone to the back side and look at it from the top.
In order to remove the back case, start by flipping the phone to the back side and look at it from the top.
1024
Step 2
Applying Pressure
- Place your finger in the small notch on the left side of the charging port (facing from the back).
- Once your finger is in the notch, pull the back case towards yourself to remove it.
Place your finger in the small notch on the left side of the charging port (facing from the back).
Once your finger is in the notch, pull the back case towards yourself to remove it.
Step 3
Battery
- Once the back case is removed, locate the battery. It is the large brick embedded in the phone. It has BLU Products, a caution statement, and a barcode on it.
- Insert your finger into the notch near the lower left of the battery, apply pressure and lift up.
Once the back case is removed, locate the battery. It is the large brick embedded in the phone. It has BLU Products, a caution statement, and a barcode on it.
Insert your finger into the notch near the lower left of the battery, apply pressure and lift up.
Step 4
Midframe
- The speaker is located behind the inner back case. Using a Phillips #0 screwdriver, unscrew the 10, 7mm screws.
- Using the Phillips #00 screwdriver, unscrew the two, 10mm screws at the bottom.
The speaker is located behind the inner back case. Using a Phillips #0 screwdriver, unscrew the 10, 7mm screws.
Using the Phillips #00 screwdriver, unscrew the two, 10mm screws at the bottom.
Step 5
Aesthetic Bottom Case
- Apply pressure and pop off the bottom aesthetic case, being careful not to break it.
Apply pressure and pop off the bottom aesthetic case, being careful not to break it.
Step 6
- Use the Spudger to pop the inner back casing off. Do this by lightly raising the side of the battery housing, then sliding the Spudger around the case.
- Pick up the inner back case and flip it over.
Use the Spudger to pop the inner back casing off. Do this by lightly raising the side of the battery housing, then sliding the Spudger around the case.
Pick up the inner back case and flip it over.
Step 7
Back Camera.
- The rear camera is located in the center of the motherboard . It is connected by a ribbon wire / prong system.
- Use tweezers to gently pop off the prong system, by pulling upwards on the black cap piece connected to the motherboard from the ribbon wire.
- Use the Tweezers to pull the camera out of the housing.
- When removing the back camera be careful not to scratch the lens, unless you are throwing it out.
The rear camera is located in the center of the motherboard . It is connected by a ribbon wire / prong system.
Use tweezers to gently pop off the prong system, by pulling upwards on the black cap piece connected to the motherboard from the ribbon wire.
Use the Tweezers to pull the camera out of the housing.
When removing the back camera be careful not to scratch the lens, unless you are throwing it out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Cody Dyl
Member since: 10/27/2014
783 Reputation
5 Guides authored
Badges:
14
+11 more badges
Team
UMass Dartmouth, Team 4-8, Miles Fall 2014
Member of UMass Dartmouth, Team 4-8, Miles Fall 2014
UMASSD-MILES-F14S4G8
2 Members
6 Guides authored
