Difficulty

Moderate

Steps

9

Time Required

                          25 - 30 minutes

Sections

2

  • Motherboard Prerequisite
  • 8 steps
  • Headphone Jack
  • 1 step

Flags

3

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackBLU Studio G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Motherboard Prerequisite
  • To remove the back cover, turn the device over, locate the safety indented notch on the bottom left corner as the screen is facing down.
  • Using your finger (or spudger), prop upwards to detach the back cover properly from the rest of the device.

To remove the back cover, turn the device over, locate the safety indented notch on the bottom left corner as the screen is facing down.

Using your finger (or spudger), prop upwards to detach the back cover properly from the rest of the device.

1024

Step 2

  • Locate the notch at the bottom of the battery for safe removal.
  • Carefully lift battery from the notch making sure not to puncture the battery rubber casting.

Locate the notch at the bottom of the battery for safe removal.

Carefully lift battery from the notch making sure not to puncture the battery rubber casting.

Step 3

  • Unscrew the 13 Phillips #0 screws from the back of the phone.

Unscrew the 13 Phillips #0 screws from the back of the phone.

Step 4

  • To remove the back panel, slide the metal spudger into 3 notches on left and right side outside edges of the device.
  • With some slow but strong pressure insert and dislodge the panel from the rest of the device. These are tough but small clips that hold together the back panel.

To remove the back panel, slide the metal spudger into 3 notches on left and right side outside edges of the device.

With some slow but strong pressure insert and dislodge the panel from the rest of the device. These are tough but small clips that hold together the back panel.

Step 5

  • Remove all 8 3.175 mm screws that secure the motherboard in place.
  • Remove by turning counter clockwise using a Phillips #0 bit with the correct screwdriver using medium/ firm pressure, assuring that you don’t strip the screws.
  • Set aside

Remove all 8 3.175 mm screws that secure the motherboard in place.

Remove by turning counter clockwise using a Phillips #0 bit with the correct screwdriver using medium/ firm pressure, assuring that you don’t strip the screws.

Set aside

Step 6

  • Locate the two connector clamps on the motherboard.
  • Carefully place the tip of a precision tweezer or metal spudger under the short light brown plastic clamp. This will release the connectors.
  • Gently pull out the connectors from the clamp inserts by pulling slowly away from of device using precision tweezers.

Locate the two connector clamps on the motherboard.

Carefully place the tip of a precision tweezer or metal spudger under the short light brown plastic clamp. This will release the connectors.

Gently pull out the connectors from the clamp inserts by pulling slowly away from of device using precision tweezers.

Step 7

  • Locate the speaker on the bottom of the device and slowly pry upwards and to the right as its wired to the motherboard.

Locate the speaker on the bottom of the device and slowly pry upwards and to the right as its wired to the motherboard.

Step 8

  • Locate the volume button strip on the left side of the device and slowly pry outwards from one end to the other from the device.
  • Carefully pull over the motherboard.

Locate the volume button strip on the left side of the device and slowly pry outwards from one end to the other from the device.

Carefully pull over the motherboard.

Step 9

              Headphone Jack
  • The headphone jack is located on the top right when face down, and is soldered onto the motherboard.
  • For assistance Identifying and re-soldering click the link for a video guide.

The headphone jack is located on the top right when face down, and is soldered onto the motherboard.

For assistance Identifying and re-soldering click the link for a video guide.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Taylor Lazaro

Member since: 04/08/2019

126 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Eastern Washington University, Team S1-G3, Rowley Spring 2019                        

                                                  Member of Eastern Washington University, Team S1-G3, Rowley Spring 2019 



                    EWU-ROWLEY-S19S1G3                     


                                            4 Members                     


                                            5 Guides authored