Blu Studio Hd 6 0 Volume Buttons Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          15 - 30 minutes            

Sections

3

• Rear Case
• 3 steps
• Midframe
• 4 steps
• Volume Buttons
• 3 steps

Flags

0

• BackBlu Studio HD 6.0

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Rear Case               

• Begin by making sure your Blu Studio is turned off.

Begin by making sure your Blu Studio is turned off.

1024

Step 2

              Back Panel.               

• To begin the removal of your back panel, first locate the lift tab on the bottom-right corner.

To begin the removal of your back panel, first locate the lift tab on the bottom-right corner.

Step 3

• Next, gently slide your thumb (or plastic tool if you prefer) down the seem running the length of your Blu Studio until the rear panel is completely removed.
• Your rear panel should be placed nearby and in a safe location until you are finished with your task.

Next, gently slide your thumb (or plastic tool if you prefer) down the seem running the length of your Blu Studio until the rear panel is completely removed.

Your rear panel should be placed nearby and in a safe location until you are finished with your task.

Step 4

              Midframe               

• With your back panel already removed from the previous guide you’ll need to acquire a Philips head screw driver size (PH00)

With your back panel already removed from the previous guide you’ll need to acquire a Philips head screw driver size (PH00)

Step 5

• Next proceed to remove all 16 screws (2.5mm in length), all screws are the same size so getting them mixed up will not be an issue later on.
• One of the lower right hand screws will be hidden under a sticker.

Next proceed to remove all 16 screws (2.5mm in length), all screws are the same size so getting them mixed up will not be an issue later on.

One of the lower right hand screws will be hidden under a sticker.

Step 6

• After removing all 16 screws you can begin the process of removing the battery housing panel.
• You will need to use the thinner plastic prying tool to slowly outline the seem of the case starting from the top (near the camera).
• Try to be careful around the side buttons as the plastic is weakest there.
• After the top half of the case has been opened insert the thicker prying tool to keep the case open. This will help as the battery and battery housing have a suction cup like action that keeps them from separating.

After removing all 16 screws you can begin the process of removing the battery housing panel.

You will need to use the thinner plastic prying tool to slowly outline the seem of the case starting from the top (near the camera).

Try to be careful around the side buttons as the plastic is weakest there.

After the top half of the case has been opened insert the thicker prying tool to keep the case open. This will help as the battery and battery housing have a suction cup like action that keeps them from separating.

Step 7

• At this point your battery, motherboard, rear camera, and front camera should all be readily available for fixing. Happy fixing.

At this point your battery, motherboard, rear camera, and front camera should all be readily available for fixing. Happy fixing.

Step 8

              Locate the volume buttons.               

• The volume buttons are located on the rear-upper-right side of your Blu Studio phone.

The volume buttons are located on the rear-upper-right side of your Blu Studio phone.

Step 9

              Replace the buttons.               

• Using the tweezers lift the volume buttons and unsolder the buttons connection.

Using the tweezers lift the volume buttons and unsolder the buttons connection.

Step 10

              Solder the new buttons.               

• Finally you solder the new buttons to the motherboard of your Blu Studio.
• Make sure that your buttons are placed as shown in the picture.

Finally you solder the new buttons to the motherboard of your Blu Studio.

Make sure that your buttons are placed as shown in the picture.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Ernesto Diaz                     

Member since: 09/23/2014

1,759 Reputation

                                      3 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges                           

Team

                       USF Tampa, Team 9-1, Blackwell Fall 2014                        

                                                  Member of USF Tampa, Team 9-1, Blackwell Fall 2014 



                    USFT-BLACKWELL-F14S9G1                     


                                            3 Members                     


                                            8 Guides authored