Difficulty

Moderate

Steps

6

Time Required

                          5 - 10 minutes

Sections

2

  • bObsweep’s cover
  • 4 steps
  • bObsweep Pethair’s LCD Screen
  • 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackbObsweep Robotic Vacuum Cleaner

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Video instructions:

What you need

Video Overview

Step 1

              bObsweep's cover
  • Flip Bob over and remove the 7 screws around which hold the cover together.
  • Remove the main brush. Unscrew the holder, and lift the brush out. Reminder: Keep this screw separate from the others so you can use it later to reinstall.
  • Depending on your model, there may be only 6 screws installed on bObsweep.

Flip Bob over and remove the 7 screws around which hold the cover together.

Remove the main brush. Unscrew the holder, and lift the brush out. Reminder: Keep this screw separate from the others so you can use it later to reinstall.

Depending on your model, there may be only 6 screws installed on bObsweep.

1024

Step 2

  • There are two screw holes inside the brush compartment: one in the centre, one on the left end. Remove both and keep aside for reassembly.
  • There are five more screws around bObsweep’s edges. Two are installed at the top and bottom, and one on the right end of the main brush.

There are two screw holes inside the brush compartment: one in the centre, one on the left end. Remove both and keep aside for reassembly.

There are five more screws around bObsweep’s edges. Two are installed at the top and bottom, and one on the right end of the main brush.

Step 3

  • Flip bOb back over so you can see the screen. Lift the cover up to reveal bObsweep’s main board.
  • Detach the power inlet from the cover. Grip and slide it out.

Flip bOb back over so you can see the screen. Lift the cover up to reveal bObsweep’s main board.

Detach the power inlet from the cover. Grip and slide it out.

Step 4

  • Remove three circuit plugs from the motherboard. Pinch the small white tab on the side of each circuit plug and pull straight up to release each from the motherboard.
    1. On the bottom left corner: a small connector with red, black and white wires.
    1. One thick white wire that attaches on the right side of the previous connector.
    1. On the top edge of bOb’s motherboard: a wide multicoloured connector.
  • Place the cover aside and begin your repair.

Remove three circuit plugs from the motherboard. Pinch the small white tab on the side of each circuit plug and pull straight up to release each from the motherboard.

  1. On the bottom left corner: a small connector with red, black and white wires.

  2. One thick white wire that attaches on the right side of the previous connector.

  3. On the top edge of bOb’s motherboard: a wide multicoloured connector.

Place the cover aside and begin your repair.

Step 5

              bObsweep Pethair's LCD Screen
  • Remove the four screws holding the screen in place
  • Lift the screen up and it will detach from the cover.

Remove the four screws holding the screen in place

Lift the screen up and it will detach from the cover.

Step 6

  • The screen and cover buttons will lift out together, leaving an open space for your replacement parts to fit into.
  • If you remove the infrared sensor, replace it in its space on the new cover so the black side will be on bOb’s outside.
  • Then, install all four screws for the LCD display. To finish off the repair, simply follow: Closing bObsweep’s cover after repair

The screen and cover buttons will lift out together, leaving an open space for your replacement parts to fit into.

If you remove the infrared sensor, replace it in its space on the new cover so the black side will be on bOb’s outside.

Then, install all four screws for the LCD display. To finish off the repair, simply follow: Closing bObsweep’s cover after repair

To reassemble your device, follow the guide for closing bObsweep after repair.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Tatiana

Member since: 06/28/2014

737 Reputation

                                      17 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges