Bose Soundlink Ii Speaker Replacement Repair Guide

Difficulty

Difficult

Steps

14

Time Required

                          6 minutes            

Sections

4

• Bose Soundlink II Cover Removal
• 2 steps
• Side Cover
• 3 steps
• Button Cover
• 4 steps
• Speaker
• 5 steps

Flags

0

• BackBose Soundlink II

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Bose Soundlink II Cover Removal               

• Using a 2.5 mm hex wrench, remove the two 13 mm screws from the bottom of the speaker.

Using a 2.5 mm hex wrench, remove the two 13 mm screws from the bottom of the speaker.

1024

Step 2

• Push up on the back of the cover until it slides up slightly.
• Pull the cover up and away from the speaker backing.

Push up on the back of the cover until it slides up slightly.

Pull the cover up and away from the speaker backing.

Step 3

              Side Cover               

• Remove the black electrical tape in order to reveal the screws attaching the side cover to the main body of the speaker. These screws are on the base of the device.

Remove the black electrical tape in order to reveal the screws attaching the side cover to the main body of the speaker. These screws are on the base of the device.

Step 4

• Using the T-10 star tip screwdriver, remove the two 13 mm screws located on the bottom of the speaker on each side of the battery pack.

Using the T-10 star tip screwdriver, remove the two 13 mm screws located on the bottom of the speaker on each side of the battery pack.

Step 5

• Slide the silver side cover down toward the base of the speaker. The silver cover will come off easily.

Slide the silver side cover down toward the base of the speaker. The silver cover will come off easily.

Step 6

              Button Cover               

• Once the Bose Soundlink II Side Covers Removal has been completed, remove the two screws (13 mm) an inch below the buttons on the back of the speaker using the T-10 star tip screwdriver.

Once the Bose Soundlink II Side Covers Removal has been completed, remove the two screws (13 mm) an inch below the buttons on the back of the speaker using the T-10 star tip screwdriver.

Step 7

• Using a tool such as a spudger or plastic opening tool, insert the end into one of the small indentations located on the back of the speaker. Start either on the indentation farthest to the right or to the left.
• Pry up with the spudger or plastic opening tool so that the cover is pushed up slightly.

Using a tool such as a spudger or plastic opening tool, insert the end into one of the small indentations located on the back of the speaker. Start either on the indentation farthest to the right or to the left.

Pry up with the spudger or plastic opening tool so that the cover is pushed up slightly.

Step 8

• Repeat this process with each of the indentations, working your way left or right (depending on where you start).

Repeat this process with each of the indentations, working your way left or right (depending on where you start).

Step 9

• Pull the cover around the buttons off. If you’d like, you can remove the button cover as well.

Pull the cover around the buttons off. If you’d like, you can remove the button cover as well.

Step 10

              Speaker               

• Pull the metal grill off of the speaker.

Pull the metal grill off of the speaker.

Step 11

• Using the T-10 star tip screwdriver, unscrew the four 13 mm screws around each of the speakers.

Using the T-10 star tip screwdriver, unscrew the four 13 mm screws around each of the speakers.

Step 12

• Lift off the cover. (You may need to pry it open)

Lift off the cover. (You may need to pry it open)

Step 13

• Unwind the wires corresponding to the speaker you want to remove (our photo shows the removal of the top right speaker).

Unwind the wires corresponding to the speaker you want to remove (our photo shows the removal of the top right speaker).

Step 14

• Carefully pop out the speaker after the wires have been unwound.

Carefully pop out the speaker after the wires have been unwound.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    John P Loughran                     

Member since: 03/02/2017

448 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       IUPUI, Team S3-G3, Harley Spring 2017                        

                                                  Member of IUPUI, Team S3-G3, Harley Spring 2017 



                    IUPUI-HARLEY-S17S3G3                     


                                            4 Members                     


                                            3 Guides authored                     

zerocool500 - Oct 1, 2018

Reply

Hello nice tutorial!

Does anyone know where can I find the #357158-0010 Speaker? thanks

Does anyone know where to find the #357158-0010 SPEAKER ? Thanks

Ramkaran Rudravaram - Dec 26, 2020

Reply

Thank you ifixit I was able remove the broken aux pin by following these steps..