Difficulty

Moderate

Steps

6

Time Required

                          10 - 15 minutes

Sections

3

  • Bottom Circuit Board Access
  • 4 steps
  • AUX/USB Port
  • 1 step
  • Bottom Circuit Board
  • 1 step

Flags

1

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackBose Soundlink Revolve

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Bottom Circuit Board Access
  • Flip speaker over so that the bottom is facing up.
  • Using the blue spudger, lift the gray foam up and slowly peel it off with your hand.

Flip speaker over so that the bottom is facing up.

Using the blue spudger, lift the gray foam up and slowly peel it off with your hand.

1024

Step 2

  • Using the screwdriver, unscrew three screws.
  • Detach the bottom cover from the rest of the speaker by pulling the two in opposite directions.

Using the screwdriver, unscrew three screws.

Detach the bottom cover from the rest of the speaker by pulling the two in opposite directions.

Step 3

  • Remove the screw that is above the charging port.

Remove the screw that is above the charging port.

Step 4

  • Remove the two screws connecting the motherboard to the bottom cover of the speaker.
  • Remove the bottom cover.

Remove the two screws connecting the motherboard to the bottom cover of the speaker.

Remove the bottom cover.

Step 5

              AUX/USB Port
  • Using the blue plastic opening tool, pry up the small black clamp connecting the AUX/USB port to the lower circuit board.
  • Remove the AUX/USB port from the device.

Using the blue plastic opening tool, pry up the small black clamp connecting the AUX/USB port to the lower circuit board.

Remove the AUX/USB port from the device.

Step 6

              Bottom Circuit Board
  • Remove the yellow tape over the location where the ribbon from the central speaker meets the bottom circuit board.
  • Use the blue plastic opening tool to pry up the black latch holding down the ribbon.
  • Remove the motherboard from the device.

Remove the yellow tape over the location where the ribbon from the central speaker meets the bottom circuit board.

Use the blue plastic opening tool to pry up the black latch holding down the ribbon.

Remove the motherboard from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 1 other contributor 


                    Brian Butner

Member since: 09/27/2017

729 Reputation

                                      3 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team S6-G2, Remmell Fall 2017                        

                                                  Member of USF Tampa, Team S6-G2, Remmell Fall 2017 



                    USFT-REMMELL-F17S6G2                     


                                            4 Members                     


                                            4 Guides authored

Gilberto - Feb 15, 2018

Reply

I need the ribbon because it is damage, can you sell one to me?

My email is ttegil@hotmail.com can you send me the way I can buy it.

Kind regards

romain thual - Oct 30, 2021

Hello do toi fond thé ribbon because i have thé same problème .

M’y email adresse thualromain44.rt@gmail.com

Thanks you

seawolf1974 - Jul 15, 2018

Reply

Hi I need bottom circuit board for bose revolve , could you sale it for me. mail: seawolf1974@mail.ru , delivery to Spain

kindly regards

Sullivan - Dec 2, 2018

Reply

I need bottom circuit board for Bose revolve, can I get it available in Nigeria, @sullivaniheme@gmail.com

Sam - Dec 11, 2018

Reply

Hey there, I also require the bottom circuit board for my Bose Revolve sam.rowlands@hotmail.com