Difficulty
Moderate
Steps
12
Time Required
20 minutes
Sections
3
- Base
- 6 steps
- Front Grill
- 3 steps
- Speakers
- 3 steps
Flags
0
BackBose Wave Radio AWR1-1W
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Base
- Remove the four 19mm Phillips #2 screws from the base of the device.
Remove the four 19mm Phillips #2 screws from the base of the device.
1024
Step 2
- Turn the device over, holding the base on with your thumbs.
- Hold the device tightly to prevent the base from falling off.
Turn the device over, holding the base on with your thumbs.
Hold the device tightly to prevent the base from falling off.
Step 3
- Gently lift the top off of the device.
- Lift in the direction shown to avoid damaging the wires connecting the top and base of the device.
Gently lift the top off of the device.
Lift in the direction shown to avoid damaging the wires connecting the top and base of the device.
Step 4
- Pinch and unplug the white connector from the device.
Pinch and unplug the white connector from the device.
Step 5
- Gently pinch and pull on the white ribbon cable to disconnect it from the base.
Gently pinch and pull on the white ribbon cable to disconnect it from the base.
Step 6
- The base should now be completely detached from the device.
The base should now be completely detached from the device.
Step 7
Front Grill
- Wedge the spudger between the top and front panel on the right side of the device.
- Push down on the spudger, lifting the front panel away from the top panel until it pops out of the right side.
- Repeat for the left side of the device.
- Too much pressure may break the panel, but it should flex slightly before it pops out.
Wedge the spudger between the top and front panel on the right side of the device.
Push down on the spudger, lifting the front panel away from the top panel until it pops out of the right side.
Repeat for the left side of the device.
Too much pressure may break the panel, but it should flex slightly before it pops out.
Step 8
- Once the panel is released on the left side, wedge the spudger between the top panel and front grill of the device as shown.
- Apply pressure and move the spudger upward until the front grill pops out.
- Repeat for the right side of the device.
Once the panel is released on the left side, wedge the spudger between the top panel and front grill of the device as shown.
Apply pressure and move the spudger upward until the front grill pops out.
Repeat for the right side of the device.
Step 9
- Lift the front grill away from the device.
Lift the front grill away from the device.
Step 10
Speakers
- Remove a total of eight 15mm Phillips #2 screws surrounding each speaker.
Remove a total of eight 15mm Phillips #2 screws surrounding each speaker.
Step 11
- Gently pull each speaker out of the device.
Gently pull each speaker out of the device.
Step 12
- Pull the wire connected to the speakers out of the device.
- You already disconnected this wire from the inside of the device earlier.
Pull the wire connected to the speakers out of the device.
You already disconnected this wire from the inside of the device earlier.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 2 other contributors
Cassie Harriman
Member since: 04/18/2017
1,015 Reputation
5 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S15-G2, Banghart Spring 2017
Member of Cal Poly, Team S15-G2, Banghart Spring 2017
CPSU-BANGHART-S17S15G2
4 Members
6 Guides authored
