Difficulty
Moderate
Steps
7
Time Required
20 minutes
Sections
2
- Access Panel
- 5 steps
- Speaker Driver
- 2 steps
Flags
0
BackBowers and Wilkins T7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Access Panel
- As with all electronic devices, make sure your device is powered off before you begin.
- Gently lift up the access panel; it should easily “pop” open.
As with all electronic devices, make sure your device is powered off before you begin.
Gently lift up the access panel; it should easily “pop” open.
1024
Step 2
- Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.
- There are 8 screws in total.
Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.
There are 8 screws in total.
Step 3
- Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.
- Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.
- The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.
Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.
Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.
The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.
Step 4
- The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.
- Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.
- As the cover starts to come off, you can lift up using your hand.
The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.
Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.
As the cover starts to come off, you can lift up using your hand.
Step 5
- Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.
- While squeezing the internal locking mechanism, pull back the terminal.
- Repeat this process for the second speaker.
Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.
While squeezing the internal locking mechanism, pull back the terminal.
Repeat this process for the second speaker.
Step 6
Speaker Driver
- Remove the 7mm screws around the speaker using a J100 Phillips head screwdriver.
- There are 4 screws in total around each speaker.
Remove the 7mm screws around the speaker using a J100 Phillips head screwdriver.
There are 4 screws in total around each speaker.
Step 7
- Now that all the screws are removed, pull straight up on the speaker drive to remove the speaker drive component.
Now that all the screws are removed, pull straight up on the speaker drive to remove the speaker drive component.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Oluwagbemisola Aderibigbe
Member since: 02/27/2017
158 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
USF Tampa, Team S7-G1, Cagle Spring 2017
Member of USF Tampa, Team S7-G1, Cagle Spring 2017
USFT-CAGLE-S17S7G1
5 Members
4 Guides authored
nigellittledesignandmedia - May 14, 2018
Reply
Where do you buy the replacement driver?
Phương Trần - Mar 17, 2019
Reply
Tôi có cùng một câu hỏi? Tôi sẽ phải mua chúng ở đâu.
