Difficulty
Difficult
Steps
8
Time Required
20 minutes
Sections
2
- Charging base wire harness
- 6 steps
- Charging base circuit board
- 2 steps
Flags
0
BackBraun Series 7 790cc
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Charging base wire harness
- Remove the cleaner cartridge from the charging base.
Remove the cleaner cartridge from the charging base.
1024
Step 2
- Depress the 4 tabs while lightly pulling the cover from the base.
- Next, depress the 2 molded tabs while still pulling the cover from the base.
Depress the 4 tabs while lightly pulling the cover from the base.
Next, depress the 2 molded tabs while still pulling the cover from the base.
Step 3
- Press inward on the side charging port while pulling cover from the base to separate.
Press inward on the side charging port while pulling cover from the base to separate.
Step 4
- Remove side charging port by prying tabs outward and rotating port upward.
Remove side charging port by prying tabs outward and rotating port upward.
Step 5
- Remove charging terminals by inserting a spudger from bottom the and sliding terminals up.
Remove charging terminals by inserting a spudger from bottom the and sliding terminals up.
Step 6
- Remove solder from circuit board and remove charging harness.
Remove solder from circuit board and remove charging harness.
Step 7
Charging base circuit board
- Remove solder from wire harness leading to the charging base motor.
Remove solder from wire harness leading to the charging base motor.
Step 8
- Use spudger to release tab at the top left of the circuit board.
- After the tab has been released the circuit board can be removed.
Use spudger to release tab at the top left of the circuit board.
After the tab has been released the circuit board can be removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Ian Hayes
Member since: 11/07/2017
198 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
IUPUI, Team S3-G6, Harley Fall 2017
Member of IUPUI, Team S3-G6, Harley Fall 2017
IUPUI-HARLEY-F17S3G6
3 Members
5 Guides authored
martin bird - Jun 2, 2019
Reply
Step 6-8
If you are only doing an investigation you can release the board enough to inspect and reconnect all connectors without desoldering. This was enough to fix my problems. I found it easier to pull the bottom of the board forward and down, rather than force the tab at the top.
Ian has also not mentioned the 3 things that can fall off, and make reassembly tricky. All these needed to be carefully stored and repositioned on my reassembly.
The Base spring release button. Although it goes on the outside I refitted to the inner unit first
The carbon/rubber button contacts in the case. These fall off when not in contact with the pcb. They fit on very fine pins on the shell button covers.
The angular molding that sits in the front of the well. Needs to be fitted completely to the Base before reassemble
Brent Bono - Mar 25, 2020
Reply
Martin, / Anyone,
Can someone provide pictures showing the reassemble process of the parts that fell out when I separated cover from the base (steps 6-8, as Martin Bird mentioned above)?
I have 2 small rubber pieces (assuming they go on the buttons on base, not exactly sure where they go), & the angular molding - not sure how this piece fits in the front somewhere?
Zebra 99 - Feb 3, 2021
Reply
I am looking the heating components.
Luca Giacca - Mar 1, 2021
Reply
But where do I find a replacement PCB?
ExpatViking - May 29, 2021
Reply
I found it hard to put the charging base back together again. Seems like something was broken, a tab or two, and it won´t close all the way down. Now there´s a gap at the bottom that I am too lazy to fix (I have already opened and closed the damned unit five times and I got bored of it.)
