Braven Brv 1M Battery Replacement Repair Guide

Difficulty

Difficult

Steps

10

Time Required

                          20 - 30 minutes            

Sections

3

• Outer Casing
• 4 steps
• Motherboard
• 4 steps
• Battery
• 2 steps

Flags

0

• BackBraven BRV-1M

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Outer Casing               

• To remove the outer casing, use a 3mm Hex bit to remove the 4 large 12mm Hex screws on both sides of the device.

To remove the outer casing, use a 3mm Hex bit to remove the 4 large 12mm Hex screws on both sides of the device.

1024

Step 2

• Using the Metal Spudger, carefully pry each side of the rubber casing away from the device.
• A little resistance should be felt, but not enough to bend the spudger.

Using the Metal Spudger, carefully pry each side of the rubber casing away from the device.

A little resistance should be felt, but not enough to bend the spudger.

Step 3

• To remove the inner plastic casing, use a Phillips #00 head bit to remove the 16 small 9mm screws surrounding the top side of the device.

To remove the inner plastic casing, use a Phillips #00 head bit to remove the 16 small 9mm screws surrounding the top side of the device.

Step 4

• Carefully lift away the housing and replace the broken casing/component. Replace using the new casing.

Carefully lift away the housing and replace the broken casing/component. Replace using the new casing.

Step 5

              Motherboard               

• To remove the motherboard, proceed to unscrew the 3 Phillips #00 bit type, 13mm long screws located on both sides of the motherboard.

To remove the motherboard, proceed to unscrew the 3 Phillips #00 bit type, 13mm long screws located on both sides of the motherboard.

Step 6

• Then, proceed to unscrew the 5 Phillips #00 bit type, 9mm long screws located on the face of the charging dock.

Then, proceed to unscrew the 5 Phillips #00 bit type, 9mm long screws located on the face of the charging dock.

Step 7

• Disconnect the two 4-pin auxiliary button register cables connected on both sides of the motherboard.

Disconnect the two 4-pin auxiliary button register cables connected on both sides of the motherboard.

Step 8

• Once disconnected, carefully remove the motherboard by pulling upwards.

Once disconnected, carefully remove the motherboard by pulling upwards.

Step 9

              Battery               

• To remove the battery, unscrew the 2 Phillips #00 bit type, 9 mm long screws on both sides of the battery.

To remove the battery, unscrew the 2 Phillips #00 bit type, 9 mm long screws on both sides of the battery.

Step 10

• Gently pull the battery from the housing of the device while disconnecting the red, white and black wires coming from the battery.

Gently pull the battery from the housing of the device while disconnecting the red, white and black wires coming from the battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Erik Oliva                     

Member since: 02/14/2018

607 Reputation

                                      6 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       USF Tampa, Team S2-G1, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S2-G1, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S2G1                     


                                            4 Members                     


                                            6 Guides authored