Difficulty

Moderate

Steps

10

Time Required

                          5 - 20 minutes

Sections

3

  • Batteries
  • 2 steps
  • Back Plate
  • 6 steps
  • Print Roller Lever
  • 2 steps

Flags

0

  • BackBrother PT-110

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Batteries
  • Push on the side of the cover, and remove it.

Push on the side of the cover, and remove it.

1024

Step 2

  • Remove the batteries.

Remove the batteries.

Step 3

              Back Plate
  • Unscrew the two 9 mm Phillips #1 screws from the top and bottom.
  • Total: 2 x Screws

Unscrew the two 9 mm Phillips #1 screws from the top and bottom.

Total: 2 x Screws

Step 4

  • First: To separate the top cover from the body, insert a spudger between the two halves.
  • Gently twist the spudger until the two halves separate. Do this in multiple spots around the perimeter of the cover to distribute the pressure.
  • DO NOT PULL HALVES APART. There are wired connections inside that must be disconnected before halves can be fully separated.

First: To separate the top cover from the body, insert a spudger between the two halves.

Gently twist the spudger until the two halves separate. Do this in multiple spots around the perimeter of the cover to distribute the pressure.

DO NOT PULL HALVES APART. There are wired connections inside that must be disconnected before halves can be fully separated.

Step 5

  • Gently separate the two covers, ensuring wires are not taut.

Gently separate the two covers, ensuring wires are not taut.

Step 6

  • Gently grasp the ribbon wire and top cover, then gently pull the ribbon wire out of its connection.

Gently grasp the ribbon wire and top cover, then gently pull the ribbon wire out of its connection.

Step 7

  • Carefully pinch the top of the connector.
  • Pull perpendicular to the device until the wire is disconnected.
  • It may require more force than expected to disconnect the wires.

Carefully pinch the top of the connector.

Pull perpendicular to the device until the wire is disconnected.

It may require more force than expected to disconnect the wires.

Step 8

  • Unscrew the three 9 mm Phillips #1 screws shown.
  • Total: 3 x Screws

Unscrew the three 9 mm Phillips #1 screws shown.

Total: 3 x Screws

Step 9

              Print Roller Lever
  • Using the metal spudger, swivel the pin so that the print roller lever loosens.

Using the metal spudger, swivel the pin so that the print roller lever loosens.

Step 10

  • Gently pull the print roller lever out.

Gently pull the print roller lever out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Kimberly Larsen

Member since: 09/28/2016

183 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       IUPUI, Team 1-1, Harley Fall 2016                        

                                                  Member of IUPUI, Team 1-1, Harley Fall 2016 



                    IUPUI-HARLEY-F16S1G1                     


                                            3 Members                     


                                            7 Guides authored

Daniel Verkest - Jul 10, 2020

Reply

Hi everybody ,does anyone knows were I can by such a lever ?

TBH

Pegase M - Dec 6, 2021

Reply

BONJOUR, (I’m French)

Same question: does anyone knows were I can by such a lever ?

Erik Carlson - Oct 20, 2022

Reply

Did anyone find a source for this part?