Difficulty
Moderate
Steps
13
Time Required
15 - 30 minutes
Sections
7
- Battery
- 2 steps
- Back of Device
- 2 steps
- Circuit Board Cables
- 2 steps
- Circuit Board
- 3 steps
- Face Plate
- 2 steps
- Keyboard
- 1 step
- LCD Screen
- 1 step
Flags
2
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
BackBrother PT-D200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.
Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.
1024
Step 2
- Remove the six AAA batteries.
Remove the six AAA batteries.
Step 3
Back of Device
- Use the Helping Hand 1/4" screwdriver to unscrew the six 3/16" corner screws.
Use the Helping Hand 1/4" screwdriver to unscrew the six 3/16" corner screws.
Step 4
- Close the back cover and then flip the device over and separate the top half from the bottom half as shown.
- Be gentle when lifting the top of the device, there is a ribbon cable attaching the two halves together.
Close the back cover and then flip the device over and separate the top half from the bottom half as shown.
Be gentle when lifting the top of the device, there is a ribbon cable attaching the two halves together.
Step 5
Circuit Board Cables
- Gently pull out the ribbon cable from the circuit board.
- The ribbon cable is very fragile.
Gently pull out the ribbon cable from the circuit board.
The ribbon cable is very fragile.
Step 6
- Remove two-pin plastic connector from the circuit board.
- Gently pull the two-pin connector from the circuit board to avoid damaging the board.
Remove two-pin plastic connector from the circuit board.
Gently pull the two-pin connector from the circuit board to avoid damaging the board.
Step 7
Circuit Board
- Remove the two 3/16" screws from the circuit board using the Helping Hand 1/4" screwdriver.
Remove the two 3/16" screws from the circuit board using the Helping Hand 1/4" screwdriver.
Step 8
- Release the two black clips that hold the LCD cable ribbon in place. To release, pull the clips towards the ribbon.
Release the two black clips that hold the LCD cable ribbon in place. To release, pull the clips towards the ribbon.
Step 9
- Disconnect the LCD ribbon cable from the circuit board.
Disconnect the LCD ribbon cable from the circuit board.
Step 10
Face Plate
- On the top portion of the device there are four grey clips locking the faceplate in place. The two top clips are circled in the image. The two others are located in the other corners of the device.
On the top portion of the device there are four grey clips locking the faceplate in place. The two top clips are circled in the image. The two others are located in the other corners of the device.
Step 11
- Pull the clips inward two at a time, first the top then the bottom, to snap the face plate off.
Pull the clips inward two at a time, first the top then the bottom, to snap the face plate off.
Step 12
Keyboard
- Peel off the rubber keyboard of the device.
Peel off the rubber keyboard of the device.
Step 13
LCD Screen
- Lift the LCD screen out of place.
Lift the LCD screen out of place.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Jeston Mitchell
Member since: 01/24/2014
308 Reputation
3 Guides authored
Badges:
4
+1 more badge
Team
Cal Poly, Team 13-16, Regan Winter 2014
Member of Cal Poly, Team 13-16, Regan Winter 2014
CPSU-REGAN-W14S13G16
3 Members
6 Guides authored
