Difficulty
Moderate
Steps
16
Time Required
Suggest a time??
Sections
3
- Rubber Casing
- 4 steps
- Speaker Grill
- 6 steps
- Speakers
- 6 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackCambridge SoundWorks OontZ Angle Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Rubber Casing
- Remove the six screw covers from the bottom of the device.
Remove the six screw covers from the bottom of the device.
1024
Step 2
- Starting from the screw covers, remove the front and back casing of the device.
Starting from the screw covers, remove the front and back casing of the device.
Step 3
- Carefully pull off the casing covering the ends.
Carefully pull off the casing covering the ends.
Step 4
- Slowly remove the casing from the top of the device.
Slowly remove the casing from the top of the device.
Step 5
Speaker Grill
- Unscrew the five 11.5mm Phillips screws from the bottom plate.
Unscrew the five 11.5mm Phillips screws from the bottom plate.
Step 6
- Carefully pull apart the bottom and top plates, using the blue plastic opening tool.
Carefully pull apart the bottom and top plates, using the blue plastic opening tool.
Step 7
- Once the plates are separated, slowly pull the bottom plate away from the top plate.
- There are wires connected to both plates, so be cautious while doing this step.
Once the plates are separated, slowly pull the bottom plate away from the top plate.
There are wires connected to both plates, so be cautious while doing this step.
Step 8
- Use the metal spudger to bend the three bendable clamps on the ends of the speaker cover.
- Beware, the bending process requires patience and extra time.
Use the metal spudger to bend the three bendable clamps on the ends of the speaker cover.
Beware, the bending process requires patience and extra time.
Step 9
- Next, use the metal spudger to bend the four bendable clamps on the bottom of the speaker cover.
- This step also requires some time and patience.
Next, use the metal spudger to bend the four bendable clamps on the bottom of the speaker cover.
This step also requires some time and patience.
Step 10
- Finally, bend the speaker cover upward and it will slide out.
Finally, bend the speaker cover upward and it will slide out.
Step 11
Speakers
- With some force, push the motherboard straight in toward the center of the device.
With some force, push the motherboard straight in toward the center of the device.
Step 12
- Pull the motherboard straight out of the device.
- There is some adhesive on the motherboard that holds it in place. This makes the motherboard fit in the groove rather tight.
Pull the motherboard straight out of the device.
There is some adhesive on the motherboard that holds it in place. This makes the motherboard fit in the groove rather tight.
Step 13
- Unplug the speaker’s connector from the motherboard.
Unplug the speaker’s connector from the motherboard.
Step 14
- Unscrew the eight screws holding the speakers in place.
Unscrew the eight screws holding the speakers in place.
Step 15
- Desolder the the wires connected to the back side of both speakers.
Desolder the the wires connected to the back side of both speakers.
Step 16
- Carefully push the speakers out one at a time.
Carefully push the speakers out one at a time.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
David Rice
Member since: 02/10/2016
161 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
USF Tampa, Team 1-1, Nance Spring 2016
Member of USF Tampa, Team 1-1, Nance Spring 2016
USFT-NANCE-S16S1G1
4 Members
6 Guides authored
