Difficulty

Moderate

Steps

10

Time Required

                          15 minutes

Sections

3

  • Front Panel
  • 4 steps
  • Top Panel
  • 4 steps
  • LCD Screen
  • 2 steps

Flags

1

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

  • BackCanon EOS 30

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Front Panel
  • Remove the two 4.8 mm black screws above the lens on the front of the camera.

Remove the two 4.8 mm black screws above the lens on the front of the camera.

1024

Step 2

  • Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.

Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.

Step 3

  • Remove the 4.8 mm black screw on the left side of the camera.

Remove the 4.8 mm black screw on the left side of the camera.

Step 4

  • Remove the front panel by lifting it away from the camera’s body.

Remove the front panel by lifting it away from the camera’s body.

Step 5

              Top Panel
  • Slide the outer eyepiece upward to remove it.

Slide the outer eyepiece upward to remove it.

Step 6

  • Remove the two 4.75 mm black screws located on the top of the camera.

Remove the two 4.75 mm black screws located on the top of the camera.

Step 7

  • Remove the four 4.3 mm black screws near the bottom corners of the eyepiece at the back of the camera.

Remove the four 4.3 mm black screws near the bottom corners of the eyepiece at the back of the camera.

Step 8

  • Slowly separate the top panel from the camera by pushing it upward.
  • Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.

Slowly separate the top panel from the camera by pushing it upward.

Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.

Step 9

              LCD Screen
  • To unclip gold connector push the edge up and away from the lcd screen. A plastic opening tool is recommended.
  • The gold connector can fall into the camera, but it will remain attached and can be pulled back up.

To unclip gold connector push the edge up and away from the lcd screen. A plastic opening tool is recommended.

The gold connector can fall into the camera, but it will remain attached and can be pulled back up.

Step 10

  • Lift LCD screen out of mount.

Lift LCD screen out of mount.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Sterling Vinson

Member since: 04/17/2011

259 Reputation

                                      5 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 8-8, Regan Spring 2011                        

                                                  Member of Cal Poly, Team 8-8, Regan Spring 2011 



                    CPSU-REGAN-S11S8G8                     


                                            5 Members                     


                                            22 Guides authored

fajar - Mar 12, 2015

Reply

Thank’s , your tutorial nice … gracias

Jasmine - Nov 19, 2017

Reply

Where do you find replacement lcd screen if the one on the camera is cracked?