Canon Eos 5D Mark Ii Lcd Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Clock Battery
3 steps
Back Panel
8 steps
LCD
2 steps

Flags

BackCanon EOS 5D Mark II
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Clock Battery

Lift the rubber flap covering the input/output jacks.

Lift the rubber flap covering the input/output jacks.

1024

Step 2

Using a Phillips #000, remove the single 3.4 mm screw.

Using a Phillips #000, remove the single 3.4 mm screw.

Step 3

This step will permanently erase all user settings.
The memory battery can now be easily slid out of place.
If you are following this guide in an effort to perform a hard reset, you should now press the shutter button multiple times in order to drain any left over power, then replace the batteries and power the device back on. You have just performed a hard reset!

This step will permanently erase all user settings.

The memory battery can now be easily slid out of place.

If you are following this guide in an effort to perform a hard reset, you should now press the shutter button multiple times in order to drain any left over power, then replace the batteries and power the device back on. You have just performed a hard reset!

Step 4

              Back Panel

Peel back the rubber cover above the in/out ports to reveal two screw heads.

Peel back the rubber cover above the in/out ports to reveal two screw heads.

Step 5

Remove both 5.4 mm screws using a Phillips #0.

Remove both 5.4 mm screws using a Phillips #0.

Step 6

Lift the in/out port plastic covering from the bottom where the backup battery used to be.

Lift the in/out port plastic covering from the bottom where the backup battery used to be.

Step 7

Remove each 6.3 mm screw on either side of the viewfinder using a Phillips #0 screwdriver.

Remove each 6.3 mm screw on either side of the viewfinder using a Phillips #0 screwdriver.

Step 8

Remove the three 4.8 mm screws on the bottom of the back plate using a Phillips #0.

Remove the three 4.8 mm screws on the bottom of the back plate using a Phillips #0.

Step 9

Peel back the rubber covering next to the menu dial to access the screw.
Remove the single 3.4 mm screw using a Phillips #0.

Peel back the rubber covering next to the menu dial to access the screw.

Remove the single 3.4 mm screw using a Phillips #0.

Step 10

The back panel can now fall off easily by turning the device upside down. Be sure to catch it so the data ribbons do not tear or tug.

The back panel can now fall off easily by turning the device upside down. Be sure to catch it so the data ribbons do not tear or tug.

Step 11

Remove each data ribbon cable from the motherboard by applying pressure down towards the motherboard and gently sliding your thumb upwards on the slot where the cable meets the motherboard. This will raise a very small clip that locks the cable in place.
The back panel is now free from the rest of the device.

Remove each data ribbon cable from the motherboard by applying pressure down towards the motherboard and gently sliding your thumb upwards on the slot where the cable meets the motherboard. This will raise a very small clip that locks the cable in place.

The back panel is now free from the rest of the device.

Step 12

LCD

Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0.

Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0.

Step 13

Grip the wire attaching the speaker to the data ribbon cable and pull it out.
The LCD is now free from the back panel.

Grip the wire attaching the speaker to the data ribbon cable and pull it out.

The LCD is now free from the back panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 1 other contributor

                    Mike Seed

Member since: 09/22/2014

2,956 Reputation

                                      8 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team 1-6, Hickman Fall 2014                        

                                                  Member of USF Tampa, Team 1-6, Hickman Fall 2014 



                    USFT-HICKMAN-F14S1G6                     


                                            3 Members                     


                                            16 Guides authored

Techtronics - Nov 19, 2015

Step 8: Missing indication to remove also the third screw on the left, just next to the connector cover

Birger Heimdal - Mar 6, 2016

where can get the lcd screen? thanks for the guide!!

hotpixelstudio - Jul 31, 2016

Big thank you! This walkthrough really helped ;) fortunatelly only one of the connecting cables slided out of the socket that caused the lcd dead. Cam is back in business in 15 minutes ;)

Pete - Sep 28, 2016

Step 2 missing indication that 2 other screws are removed near lower input/output jacks just above

memory battery location.

Also….the last step should mention unclipping the ribbon cables in the same manner as before from the small circuit board that resides on the rear of the LCD, and the LCD has a metal frame that will need to be removed and installed on the replacement LCD before installing it. It is held in place via strong double sided tape. A little heat may need to be applied to separate it.

Introduction#

What you need#

Team#

Introduction

What you need

Team