Difficulty
Moderate
Steps
15
Time Required
20 - 40 minutes
Sections
3
- Rear LCD Screen Dissasembly
- 4 steps
- Removing Rear Cover
- 8 steps
- LCD Screen Swivel Assembly
- 3 steps
Flags
0
BackCanon EOS 60D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear LCD Screen Dissasembly
- Take the LCD out of its place to expose the Phillips #PH00 screws.
- Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.
- Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.
Take the LCD out of its place to expose the Phillips #PH00 screws.
Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.
Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.
1024
Step 2
- Using a plastic opening tool, carefully pry off the back cover of the LCD.
Using a plastic opening tool, carefully pry off the back cover of the LCD.
Step 3
- Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.
- Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.
Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.
Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.
Step 4
- Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.
Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.
Step 5
Removing Rear Cover
- Now, four 2.2 mm Phillips #PH00 screws holding a cover around the hinge should be visible.
- Turn the swivel around to expose the remaining of the aforementioned screws.
- Then use the PH00 screw driver to remove them.
Now, four 2.2 mm Phillips #PH00 screws holding a cover around the hinge should be visible.
Turn the swivel around to expose the remaining of the aforementioned screws.
Then use the PH00 screw driver to remove them.
Step 6
- The eye piece will slide right off with a firm push upwards.
- Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.
- Remove the two 9.9 mm Phillips #PH00 screws using the PH00 screwdriver.
The eye piece will slide right off with a firm push upwards.
Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.
Remove the two 9.9 mm Phillips #PH00 screws using the PH00 screwdriver.
Step 7
- Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.
Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.
Step 8
- Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera.
- Remove the four different sized screws located beneath the rubber grip.
- 6 mm Phillips #PH00 screw.
- 3.4 mm Phillips #PH00 screw.
- 3.9 mm Phillips #PH00 screw.
- 2.2 mm Phillips #PH00 screw.
Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera.
Remove the four different sized screws located beneath the rubber grip.
6 mm Phillips #PH00 screw.
3.4 mm Phillips #PH00 screw.
3.9 mm Phillips #PH00 screw.
2.2 mm Phillips #PH00 screw.
Step 9
- Using the plastic opening tool, carefully pry off the the side cover.
Using the plastic opening tool, carefully pry off the the side cover.
Step 10
- Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.
Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.
Step 11
- Look at the bottom of the camera so the serial number tag reads up right.
- Using the PH00 screw driver, remove the top three 3.5 mm Phillips #PH00 screws.
Look at the bottom of the camera so the serial number tag reads up right.
Using the PH00 screw driver, remove the top three 3.5 mm Phillips #PH00 screws.
Step 12
- Now gently pull the back cover off the camera.
- Gently pull the orange wire connected to the motherboard of the camera up and off of the motherboard.
Now gently pull the back cover off the camera.
Gently pull the orange wire connected to the motherboard of the camera up and off of the motherboard.
Step 13
LCD Screen Swivel Assembly
- Carefully pry off the LCD screen connector up from the motherboard to disconnect it, using the plastic opening tool.
Carefully pry off the LCD screen connector up from the motherboard to disconnect it, using the plastic opening tool.
Step 14
- Remove one 2.8 mm Phillips #PH00 black screw on the side of the swivel assembly by using the PH00 screwdriver.
Remove one 2.8 mm Phillips #PH00 black screw on the side of the swivel assembly by using the PH00 screwdriver.
Step 15
- Remove the two 2.8 mm Phillips #PH00 black screws on the back of the swivel assembly using the PH00 screwdriver.
Remove the two 2.8 mm Phillips #PH00 black screws on the back of the swivel assembly using the PH00 screwdriver.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 4 other contributors
Alejandro Cabrera
Member since: 08/25/2015
413 Reputation
2 Guides authored
Badges:
13
+10 more badges
Team
USF Tampa, Team 16-6, Wollert Fall 2015
Member of USF Tampa, Team 16-6, Wollert Fall 2015
USFT-WOLLERT-F15S16G6
3 Members
14 Guides authored
yoeldiamante - Jun 16, 2017
Reply
anybody know how to fix the conection that make the screen turn upside down?
thank you for the tutorial. but it is so wrong, there is no way to reasambly following the steps backward. do it for your self and you will see. there are skipping steps in the disassembly. carefoul anybody who follow this tutorial. i got lost in the reasambly. hope to can figure it out.
