Canon Eos 60D Rear Cover Removal Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Rear LCD Screen Dissasembly
4 steps
Removing Rear Cover
8 steps

Flags

BackCanon EOS 60D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear LCD Screen Dissasembly

Take the LCD out of its place to expose the Phillips #PH00 screws.
Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.
Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.

Take the LCD out of its place to expose the Phillips #PH00 screws.

Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.

Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.

1024

Step 2

Using a plastic opening tool, carefully pry off the back cover of the LCD.

Using a plastic opening tool, carefully pry off the back cover of the LCD.

Step 3

Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.
Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.

Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.

Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.

Step 4

Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.

Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.

Step 5

              Removing Rear Cover

Now, four 2.2 mm Phillips #PH00 screws holding a cover around the hinge should be visible.
Turn the swivel around to expose the remaining of the aforementioned screws.
Then use the PH00 screw driver to remove them.

Now, four 2.2 mm Phillips #PH00 screws holding a cover around the hinge should be visible.

Turn the swivel around to expose the remaining of the aforementioned screws.

Then use the PH00 screw driver to remove them.

Step 6

The eye piece will slide right off with a firm push upwards.
Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.
Remove the two 9.9 mm Phillips #PH00 screws using the PH00 screwdriver.

The eye piece will slide right off with a firm push upwards.

Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.

Remove the two 9.9 mm Phillips #PH00 screws using the PH00 screwdriver.

Step 7

Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.

Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.

Step 8

Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera.
Remove the four different sized screws located beneath the rubber grip.
6 mm Phillips #PH00 screw.
3.4 mm Phillips #PH00 screw.
3.9 mm Phillips #PH00 screw.
2.2 mm Phillips #PH00 screw.

Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera.

Remove the four different sized screws located beneath the rubber grip.

6 mm Phillips #PH00 screw.

3.4 mm Phillips #PH00 screw.

3.9 mm Phillips #PH00 screw.

2.2 mm Phillips #PH00 screw.

Step 9

Using the plastic opening tool, carefully pry off the the side cover.

Using the plastic opening tool, carefully pry off the the side cover.

Step 10

Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.

Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.

Step 11

Look at the bottom of the camera so the serial number tag reads up right.
Using the PH00 screw driver, remove the top three 3.5 mm Phillips #PH00 screws.

Look at the bottom of the camera so the serial number tag reads up right.

Using the PH00 screw driver, remove the top three 3.5 mm Phillips #PH00 screws.

Step 12

Now gently pull the back cover off the camera.
Gently pull the orange wire connected to the motherboard of the camera up and off of the motherboard.

Now gently pull the back cover off the camera.

Gently pull the orange wire connected to the motherboard of the camera up and off of the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Tyler Vaal

Member since: 08/30/2015

659 Reputation

                                      3 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team 16-6, Wollert Fall 2015                        

                                                  Member of USF Tampa, Team 16-6, Wollert Fall 2015 



                    USFT-WOLLERT-F15S16G6                     


                                            3 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team