Canon Eos 60D Rear Lcd Screen Protective Plastic Cover Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Rear LCD Screen Dissasembly
4 steps
Rear LCD Screen
2 steps
Rear LCD screen protective plastic cover
3 steps

Flags

BackCanon EOS 60D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear LCD Screen Dissasembly

Take the LCD out of its place to expose the Phillips #PH00 screws.
Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.
Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.

Take the LCD out of its place to expose the Phillips #PH00 screws.

Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.

Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.

1024

Step 2

Using a plastic opening tool, carefully pry off the back cover of the LCD.

Using a plastic opening tool, carefully pry off the back cover of the LCD.

Step 3

Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.
Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.

Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.

Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.

Step 4

Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.

Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.

Step 5

              Rear LCD Screen

Remove the two 2.5 mm Phillips #PH00 silver screws using the PH00 screwdriver.
Using the plastic Spudger opening tool, carefully lift up on the medal tabs next to where the screws were located.

Remove the two 2.5 mm Phillips #PH00 silver screws using the PH00 screwdriver.

Using the plastic Spudger opening tool, carefully lift up on the medal tabs next to where the screws were located.

Step 6

Finally, remove the LCD screen by grabbing the clear plastic tab and lifting it carefully.

Finally, remove the LCD screen by grabbing the clear plastic tab and lifting it carefully.

Step 7

              Rear LCD screen protective plastic cover

Slowly insert the tip of the Jimmy between the damaged plastic cover and the plastic frame, which holds it, to loosen the connection between them.
The Jimmy is sharp, so take special care when using it to avoid damaging the plastic frame or causing personal injury.

Slowly insert the tip of the Jimmy between the damaged plastic cover and the plastic frame, which holds it, to loosen the connection between them.

The Jimmy is sharp, so take special care when using it to avoid damaging the plastic frame or causing personal injury.

Step 8

Carefully slide the Jimmy through all corners of the plastic frame until it is detached from the plastic cover.

Carefully slide the Jimmy through all corners of the plastic frame until it is detached from the plastic cover.

Step 9

Using your hand, lift the detached plastic cover off the plastic frame.
To place a new plastic cover, simply stick it to the frame in the appropriate position.

Using your hand, lift the detached plastic cover off the plastic frame.

To place a new plastic cover, simply stick it to the frame in the appropriate position.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Nazmi Bargouthi

Member since: 08/26/2015

576 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team 16-6, Wollert Fall 2015                        

                                                  Member of USF Tampa, Team 16-6, Wollert Fall 2015 



                    USFT-WOLLERT-F15S16G6                     


                                            3 Members                     


                                            14 Guides authored

Oliver Stietz - Oct 4, 2016

I followed all the steps and was able to dis- and reassamble everything in under 30min. When you reassamble make sure that in step 4 the metalplate of the housing is turned correctly and the connector is in the right position. Both could be turned 180° and mounted incorrectly. Other than that easy repair.

Thanks guys

Claudio Dantas - Dec 26, 2017

Hi there, can anyone send me some amazon link so I can order the correct glass? Thanks so far.

Introduction#

What you need#

Team#

Introduction

What you need

Team