Featured
Featured Guide
Difficulty
Difficult
Steps
10
Time Required
Suggest a time??
Sections
5
- Latch Side Cover
- 2 steps
- Disassembling Canon EOS Rebel XS Front Cover
- 2 steps
- Back Cover
- 2 steps
- Top Panel
- 3 steps
- Interior Eyepiece
- 1 step
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackCanon EOS Rebel XS / 1000D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Latch Side Cover
- Remove the two 3mm (1/8") black screws from the side cover using a #00 Phillips screwdriver.
Remove the two 3mm (1/8") black screws from the side cover using a #00 Phillips screwdriver.
1024
Step 2
- On the bottom, remove the 6mm (13/64") screw with the #00 Phillips Screwdriver.
- Pry up the panel; starting from the front/bottom corner, as indicated.
- There’s a concealed lip, under the opposite edge.
On the bottom, remove the 6mm (13/64") screw with the #00 Phillips Screwdriver.
Pry up the panel; starting from the front/bottom corner, as indicated.
There’s a concealed lip, under the opposite edge.
Step 3
Disassembling Canon EOS Rebel XS Front Cover
- Remove three medium length screws from the bottom of the camera
Remove three medium length screws from the bottom of the camera
Step 4
- Remove the two medium length screws on the front panel of the camera above the lens mount.
- Once you done, you may use the Spudger to panel from non-grip side.
- If you start on the grip side, it will be more challenging to loosen the panel.
Remove the two medium length screws on the front panel of the camera above the lens mount.
Once you done, you may use the Spudger to panel from non-grip side.
If you start on the grip side, it will be more challenging to loosen the panel.
Step 5
Back Cover
- Remove the three long black screws from the bottom using a #00 Phillips screwdriver.
- Use tweezers to lift the panel.
Remove the three long black screws from the bottom using a #00 Phillips screwdriver.
Use tweezers to lift the panel.
Step 6
- Once you have detached the back cover, use a pair of tweezers to lightly pull on strap found connecting the back cover to the camera.
Once you have detached the back cover, use a pair of tweezers to lightly pull on strap found connecting the back cover to the camera.
Step 7
Top Panel
- Remove the following ribbons with the tweezers by gently pulling on them.
- Remove the three black screws, near the eye piece, using the Phillips Screwdriver.
Remove the following ribbons with the tweezers by gently pulling on them.
Remove the three black screws, near the eye piece, using the Phillips Screwdriver.
Step 8
- Remove the cable heads attached on the front side of the camera next to the lens mount.
- Be gentle when puling wires lose, use the tweezers to remove the wires.
Remove the cable heads attached on the front side of the camera next to the lens mount.
Be gentle when puling wires lose, use the tweezers to remove the wires.
Step 9
- You can use your fingers to pull the top panel of the camera.
You can use your fingers to pull the top panel of the camera.
Step 10
Interior Eyepiece
- After removing the top panel, you can use your fingers to remove the eye piece from the camera.
After removing the top panel, you can use your fingers to remove the eye piece from the camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Daniel Bussone
Member since: 01/28/2011
1,251 Reputation
11 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 3-41, Regan Winter 2011
Member of Cal Poly, Team 3-41, Regan Winter 2011
CPSU-REGAN-W11S3G41
2 Members
21 Guides authored
Erik - Jun 25, 2014
Reply
Is there a part number to order the interior eyepiece? It does me no good to take it apart if I don’t have or can’t find a replacement for it.
rideswchrist - Sep 27, 2019
Reply
How do you replace the internal battery?
